- Community Home
- >
- Servers and Operating Systems
- >
- Legacy
- >
- HPE 9000 and HPE e3000 Servers
- >
- Re: MP console not working
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-06-2003 04:49 PM
тАО11-06-2003 04:49 PM
MP console not working
Here we r using 9000/800/rp7410.I can not able to get my MP console through serial console port. MP login prompt is not comming.my LAN console also not functioning when i try to ping my lan console it gives "Request Timed out".Two days before it was fine.How can i check my console status.There is no fault indication in my front LED panel,"MPpresent" LED also glowing.How to recover my console without restarting the server.My terminal is fine it is working with another same server.
reg
Mohan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-06-2003 05:06 PM
тАО11-06-2003 05:06 PM
Re: MP console not working
Get a laptop with windows paltform and connect the server directly to the laptop via a parallel cable, then configure the Hyper Terminal in the laptop to connect using the parallel cable. If the login prompt comes up, then it's not the cable at least. Another way:
1. Turn off the power to the console, hold the "d" key down and while holding it down power it back on. Release the d key after about 10-12 seconds, and the terminal should then display something like "Default Configs Used" in the lower left hand side. Hit the Return key, and that should fix the issue.
2. If whatever you type just echos on the screen, then perhaps the Remote Mode is turned off. Pressing F4 should turn it back on and you should see the asterisk.
Good luck
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-06-2003 08:56 PM
тАО11-06-2003 08:56 PM
Re: MP console not working
I did what u said.But it is not giving proper output.I found one switch mpreset in MP/SCSI board.what will happen if i reset.at cast my server should not get reboot.
Mohan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-06-2003 09:20 PM
тАО11-06-2003 09:20 PM
Re: MP console not working
I haven't tried that but I we did was to turn the console off.
unplg the cable from both ends.
plug the cable back in and turn on the Console. It worked!
I'm not sure if you reset what will happen.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-06-2003 11:26 PM
тАО11-06-2003 11:26 PM
Re: MP console not working
Couple of things:
1) rp7410 can have 2 MP cards. Make sure you're plugged into the console for the proper MP if you have 2 MP cards.
2) On the MP card - just below the SCSI connector - is an MP Reset button. Press that - you'll need a small screwdriver or ball point pen & try this again.
HTH,
Jeff
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-06-2003 11:27 PM
тАО11-06-2003 11:27 PM
Re: MP console not working
NO, only the MP will be reset. The system wil NOT reboot.
Rgds,
Jeff
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-07-2003 02:14 AM
тАО11-07-2003 02:14 AM
Re: MP console not working
In my setup only one MP card is there.
IN that card LED indication MP/Power,Lan,activity,self test indications are fine.For MP console any timeout value is there.How can i check the MP related things in OS level.I mean any device file there according to MP console.
pls conform if i reset the mpreset button my server should not be reboot,If server get's reboot i will be in big trouble..
thanks and reg
Mohan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-07-2003 03:08 PM
тАО11-07-2003 03:08 PM
Re: MP console not working
If you have access to the knowledge base, you'll find helpful guidelines to give a concept of what's going on!
Here is one document:
http://www2.itrc.hp.com/service/cki/cache/200000065004697.pdf
http://www2.itrc.hp.com/service/cki/cache/200000065004706.pdf
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-09-2003 06:36 PM
тАО11-09-2003 06:36 PM
Re: MP console not working
I reset my MPreset.But no improvement..
I found that PCI Power supply is in off condition.How can I switch on PCI Power supply without restarting my server.My MP console also still not working.I don't know Because of this PCI powersupply MP console is not functioning..?how to come out from this?
reg Mohan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-09-2003 06:36 PM
тАО11-09-2003 06:36 PM
Re: MP console not working
I reset my MPreset.But no improvement..
I found that one of the PCI Power supply is in off condition.How can I switch on PCI Power supply without restarting my server.My MP console also still not working.I don't know Because of this PCI powersupply MP console is not functioning..?how to come out from this?
reg Mohan