HPE 9000 and HPE e3000 Servers
cancel
Showing results for 
Search instead for 
Did you mean: 

My L2000 unable to boot and keeps SYSTEM ELERT

 
Shukor
Frequent Advisor

My L2000 unable to boot and keeps SYSTEM ELERT

Hi There,

My L2000 suddently reboot and keeps receiving SYSTEM ELERT. OS cannot UP even I knowledged the error. TQ in adv. The error output like this:

************* SYSTEM ALERT **************
SYSTEM NAME: uninitialized
DATE: 05/07/2009 TIME: 05:42:59
ALERT LEVEL: 3 = System blocked waiting for operator input

REASON FOR ALERT
SOURCE: 1 = processor
SOURCE DETAIL: 1 = processor general SOURCE ID: 0
PROBLEM DETAIL: 0 = no problem detail

LEDs: RUN ATTENTION FAULT REMOTE POWER
FLASH FLASH FLASH ON ON
LED State: Unexpected Reboot. Running non-OS code. Non-critical error detected.
Check Chassis and Console Logs for error messages.

0xF8E010301100EFFF 00000000 0000EFFF - type 31 = legacy PA HEX chassis-code
0x58E018301100EFFF 00006D04 07052A3B - type 11 = Timestamp 05/07/2009 05:42:59
A: ack read of this entry - X: Disable all future alert messages
Anything else skip redisplay the log entry
->Choice:
6 REPLIES 6
Torsten.
Acclaimed Contributor

Re: My L2000 unable to boot and keeps SYSTEM ELERT

Do as advised: "Check Chassis and Console Logs for error messages."

Hope this helps!
Regards
Torsten.

__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.

__________________________________________________
No support by private messages. Please ask the forum!

If you feel this was helpful please click the KUDOS! thumb below!   
Shukor
Frequent Advisor

Re: My L2000 unable to boot and keeps SYSTEM ELERT

Thanks torsten, but need your advice how to Check Chassis and Console Logs for error messages.
Torsten.
Acclaimed Contributor

Re: My L2000 unable to boot and keeps SYSTEM ELERT

Go to the GSP and do

GSP> sl


SL

Select Chassis Code Buffer to be displayed:
Incoming, Activity, Error, Current boot or Last boot? (I/A/E/C/L) e
e

Set up filter options on this buffer? (Y/[N]) n


The first entry is the most recent Chassis Code
Type + CR and CR to go up (back in time),
Type - CR and CR to go down (forward in time),
Type Q/q CR to quit.


Hope this helps!
Regards
Torsten.

__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.

__________________________________________________
No support by private messages. Please ask the forum!

If you feel this was helpful please click the KUDOS! thumb below!   
Shukor
Frequent Advisor

Re: My L2000 unable to boot and keeps SYSTEM ELERT

I've got 3 log entries,

SOURCE: 1 = processor
SOURCE DETAIL: 1 = processor general SOURCE ID: 0
PROBLEM DETAIL: 0 = no problem detail

SOURCE: 1 = processor
SOURCE DETAIL: 1 = processor general SOURCE ID: 0
PROBLEM DETAIL: 0 = no problem detail

SOURCE: 8 = I/O
SOURCE DETAIL: 2 = system bus adapter SOURCE ID: 7
PROBLEM DETAIL: 3 = function failure


Torsten, what does its mean and what should I do now?
Torsten.
Acclaimed Contributor

Re: My L2000 unable to boot and keeps SYSTEM ELERT

Not enough information to be sure, but

SOURCE DETAIL: 2 = system bus adapter SOURCE ID: 7
PROBLEM DETAIL: 3 = function failure

points to a problem either with the system board or the PCI board.

Hope this helps!
Regards
Torsten.

__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.

__________________________________________________
No support by private messages. Please ask the forum!

If you feel this was helpful please click the KUDOS! thumb below!   
Shukor
Frequent Advisor

Re: My L2000 unable to boot and keeps SYSTEM ELERT

Thanks!