- Community Home
- >
- Servers and Operating Systems
- >
- Legacy
- >
- HPE 9000 and HPE e3000 Servers
- >
- Re: Navigation around console and GSP on rp7410 sy...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-09-2004 06:33 AM
тАО09-09-2004 06:33 AM
Navigation around console and GSP on rp7410 systems
We have two rp7410 HP-UX machines on site. The command of the GSP is quite different from the rp5450 model.
I got into the MP:CM> prompt and don't know how to get out.
Please let me know how can I navigate around this device and better yet, if you have any online document I will be very appreciated.
Thanks,
Vu
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-09-2004 06:43 AM
тАО09-09-2004 06:43 AM
Re: Navigation around console and GSP on rp7410 systems
from MP:CM> prompt enter ma command to go to the main menu.
Some information about MP navigation is included in
http://www.docs.hp.com/hpux/onlinedocs/A7025-96010-en/A7025-96010-en.pdf
see page 60->
Regards,
Zygmunt
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-09-2004 06:45 AM
тАО09-09-2004 06:45 AM
Re: Navigation around console and GSP on rp7410 systems
This is a cell based system and the MP navigation will be slight different from non-cell based systems.
Look at the following document on GSP
http://docs.hp.com/hpux/onlinedocs/B2355-90702/B2355-90702.html
Chapter " Superdome Console and Service Interface "
-Sri
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-09-2004 06:50 AM
тАО09-09-2004 06:50 AM
Re: Navigation around console and GSP on rp7410 systems
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-10-2004 02:19 AM
тАО09-10-2004 02:19 AM
Re: Navigation around console and GSP on rp7410 systems
The
HE
command will show you a list of commands available in the command menu. Many are the same as the previous PA-RISC systems:
LC - lan console configuration
RS - Reset a Partition
CA - configure console serial port
ER - Enable remote access
DR - Disable remote access
What are you needing to do?
Josh