HPE 9000 and HPE e3000 Servers
cancel
Showing results for 
Search instead for 
Did you mean: 

Problem with RP4440

 
JorgeH
Occasional Advisor

Problem with RP4440

Hi,

I have 2 rp4440 and copy a Hard Disk(HPUX 11.23) for one of the rp4440(firmware 44.21, CPU 900MHZ). I want to use the copy of hard disk in my second rp4440(firmware 45.11, CPU 1000MHZ). When I boot the second rp4440 with the copy of the hard disk the system stop. The problem is this:

Main Menu: Enter command or menu > bo
Interact with IPL (Y, N, or Cancel)?> y

Booting...
Boot IO Dependent Code (IODC) revision 3


HARD Booted.

ISL Revision A.00.43 Apr 12, 2000

ISL> hpux

Boot
: disk(0/1/1/0.1.0.0.0.0.0;0)/stand/vmunix
10846208 + 1900544 + 1382056 start 0x1fbbe8




alloc_pdc_pages: Relocating PDC from 0xfffffff0f0c00000 to 0x3f900000.
gate64: sysvec_vaddr = 0xc0002000 for 2 pages
NOTICE: nfs3_link(): File system was registered at index 3.
NOTICE: autofs_link(): File system was registered at index 6.
NOTICE: cachefs_link(): File system was registered at index 7.

System Console is on the Built-In Serial Interface
Swap device table: (start & size given in 512-byte blocks)
entry 0 - auto-configured on root device; ignored - can't open device
WARNING: no swap device configured, so dump cannot be defaulted to primary swap.
WARNING: No dump devices are configured. Dump is disabled.
mountfs:opend

linkstamp: Mon Jan 5 17:44:46 MST 2004
_release_version: @(#) $Revision: vmunix: vw: -proj selectors: CUPI80_BL2000_1108 -c 'Vw for CUPI80_BL2000_1108 build' -- cupi80_bl2000_1108 'CUPI80_BL2000_1108' Wed Nov 8 19:24:56 PST 2000 $
panic: all VFS_MOUNTROOTs failed: NEED DRIVERS ?????

PC-Offset Stack Trace (read across, top of stack is 1st):
0x0020e138 0x00305660 0x00369c6c
0x0048321c 0x00369f48 0x00176f4c
0x001fc1e4
End Of Stack




Firmware Version 45.11

Duplex Console IO Dependent Code (IODC) revision 1



Stored message buffer up to panic:
gate64: sysvec_vaddr = 0xc0002000 for 2 pages
NOTICE: nfs3_link(): File system was registered at index 3.
NOTICE: autofs_link(): File system was registered at index 6.
NOTICE: cachefs_link(): File system was registered at index 7.
0 sba
0/0 lba
0/0/1/0 asio0
0/0/1/1 asio0
0/0/2/0 hcd
0/0/2/0.1 hub
0/0/2/1 hcd
0/0/2/1.1 hub
0/0/2/2 ehci
0/0/3/0 side_ba
0/0/3/0.0 side
0/0/3/0.0.7 tgt
0/0/3/0.0.7.0 sctl
0/0/3/0.1 side
0/0/3/0.1.7 tgt
0/0/3/0.1.7.0 sctl
0/1 lba
0/2 lba
0/4 lba
0/5 lba
0/6 lba
8 memory
16 ipmi
128 processor
129 processor
136 processor
137 processor
144 processor
145 processor
152 processor
153 processor

System Console is on the Built-In Serial Interface
Swap device table: (start & size given in 512-byte blocks)
entry 0 - auto-configured on root device; ignored - can't open device
WARNING: no swap device configured, so dump cannot be defaulted to primary swap.
WARNING: No dump devices are configured. Dump is disabled.
mountfs:opend

System Panic:

linkstamp: Mon Jan 5 17:44:46 MST 2004
_release_version: @(#) $Revision: vmunix: vw: -proj selectors: CUPI80_BL2000_1108 -c 'Vw for CUPI80_BL2000_1108 build' -- cupi80_bl2000_1108 'CUPI80_BL2000_1108' Wed Nov 8 19:24:56 PST 2000 $
panic: all VFS_MOUNTROOTs failed: NEED DRIVERS ?????

PC-Offset Stack Trace (read across, top of stack is 1st):
0x0020e138 0x00305660 0x00369c6c
0x0048321c 0x00369f48 0x00176f4c
0x001fc1e4
End Of Stack

sync'ing disks (0 buffers to flush): (0 buffers to flush):
0 buffers not flushed
0 buffers still dirty


Firmware Version 45.11

Duplex Console IO Dependent Code (IODC) revision 1
------------------------------------------------------------------------------
(c) Copyright 1995-2004, Hewlett-Packard Company, All rights reserved
------------------------------------------------------------------------------

Processor Speed State CoProcessor State Cache Size
Number State Inst Data
--------- -------- --------------------- ----------------- ------------
0 1000 MHz Active Functional 67108864 67108864
1 1000 MHz Idle Functional 67108864 67108864
2 1000 MHz Idle Functional 67108864 67108864
3 1000 MHz Idle Functional 67108864 67108864
4 1000 MHz Idle Functional 67108864 67108864
5 1000 MHz Idle Functional 67108864 67108864
6 1000 MHz Idle Functional 67108864 67108864
7 1000 MHz Idle Functional 67108864 67108864

Central Bus Speed (in MHz) : 200
Available Memory : 4194304 KB
Good Memory Required : Not initialized. Defaults to 32 MB.

Primary boot path: 0/1/1/0.1
Alternate boot path: 0/1/1/1.0
Console path: 0/0/1/1.0
Keyboard path: 0/0/4/0.0


*** A system crash has occurred. (See the above messages for details.)
*** The system is now preparing to

ERROR: No dump space is configured. Physical memory will not be dumped.



The only change in this two servers is the fiwmware version and the processors, I boot the first rp4440 with the copy of the hard disk and didn't have problem the system boot perfect, but in the second server have this problem.Please help me.
5 REPLIES 5
Sameer_Nirmal
Honored Contributor

Re: Problem with RP4440

Hi,

Try to boot the system as
ISL> hpux -lq

Well, there are other causes for such panic
like wrong contents of Autofile , corrupt BDRA, missing driver due to bad or corrupt kernel.

You can also try
ISL> hpux /stand/vmunix.prev
JorgeH
Occasional Advisor

Re: Problem with RP4440

Thanks Sameer, but I use the two commands and have the same problem. what other way can use to fix this problem.
Ted Buis
Honored Contributor

Re: Problem with RP4440

How did you make the disk copy?

The two systems are different, so maybe there is a difference in the kernel for the different clock rates.

You may need to use Ignite/UX?s
Mom 6
JorgeH
Occasional Advisor

Re: Problem with RP4440

ok. I copy the HD with dd if=89789 of=98980 bs=4096(example only).The scsi card is diferent too. I interchange the SCSI card and the system boot whitout problem. I want to configure the SCSI of the second HD but I dont know the steps.help me please
Ted Buis
Honored Contributor

Re: Problem with RP4440

Are these internal or external drives? Can you be more specific about the configurations? Which SCSI interface part numbers. It is possible to have an rp4440 configured with the two internal disks daisy chained off one of the standard SCSI (Core I/O) ports. If this is the case then, the SCSI port that connects the internal disks cannot be used for external connections. If the rp4440 was purchased with the duplex SCSI option (A9740A) then each internal disk is one a separate SCSI us and in this case, neither of the two internal SCSI buses can be used for external connections. Are you trying to use a SCSI port for external use that is also being used for internal use? This won't work.
Mom 6