- Community Home
- >
- Servers and Operating Systems
- >
- Legacy
- >
- HPE 9000 and HPE e3000 Servers
- >
- Re: RP 7410 Dual core I/O problems
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-20-2006 11:35 PM
тАО09-20-2006 11:35 PM
Can anyone help?
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-22-2006 01:29 AM
тАО09-22-2006 01:29 AM
SolutionTo check the status you can use PS or try PE command and turn them ON:
MP:CM> pe
select P for I/o cage and then select 0 or 1 and then turn them ON one by one.. then check the status of the devices. ( Since Core i/o is not installed in I/o chasis you could see them).
Please let me know the outcome...
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-22-2006 03:07 AM
тАО09-22-2006 03:07 AM
Re: RP 7410 Dual core I/O problems
The PCI power supplies are both OK, & both I/O chassis are powered on. I have attached the I/O information for chassis 0 from partition manager. There seems to be a problem with the PCI bus on chassis 0 would this be the cause of the internal disks not being found on partition 1?
Thanks
Jez.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-28-2006 08:58 AM
тАО09-28-2006 08:58 AM
Re: RP 7410 Dual core I/O problems
Also worth noting is that the top drive slots are seen by cell/npar 1 while the bottom ones are assigned to cell/npar 0 (the DVD is only seen by cell/npar 1).
You will not be able to connect to your second MP board as there can only be one active at a time. By default the active one is in slot 1.
I hope this info helps you out.
-Bob
Was this helpful? Like this post by giving me a thumbs up below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-01-2006 07:52 PM
тАО10-01-2006 07:52 PM
Re: RP 7410 Dual core I/O problems
Both SCSI/LAN boards are located in the outermost slots, HP suggested that I changed the initiator address in the service menu on one of the SCSI boards which had no effect. They suggested that I deleted par1 & added the second cell to par0. All the PCI slots in par0 are available and ioscan claimed the dvdrom on the second SCSI/LAN. HP informed me that with both cells in one partition all four disk in the drive bays should be available is this true.
Thanks,
Jez.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-06-2006 08:55 AM
тАО10-06-2006 08:55 AM
Re: RP 7410 Dual core I/O problems
-Bob
Was this helpful? Like this post by giving me a thumbs up below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-08-2006 12:43 AM
тАО10-08-2006 12:43 AM
Re: RP 7410 Dual core I/O problems
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-08-2006 04:47 AM
тАО10-08-2006 04:47 AM
Re: RP 7410 Dual core I/O problems
I have updated all of the entities with the latest firmware, PDC, PCI, MP ect.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-21-2007 01:52 AM
тАО06-21-2007 01:52 AM
Re: RP 7410 Dual core I/O problems
I have had two RP7410 servers with this same problem I have now bought a new RP7410 server chassis & with the parts from the others i.e. MP, LAN, cell boards I have successfully created two partitions & installed HP UX 11.11 on both of them.
I am wondering if there is a glitch with some of the early versions of this server that has since been rectified.
Jez.