HPE 9000 and HPE e3000 Servers
cancel
Showing results for 
Search instead for 
Did you mean: 

RP7410 PDC error, CELL 1 don't power on

 
Aleksey Shkil_1
Occasional Advisor

RP7410 PDC error, CELL 1 don't power on

Hello friends! I have some throble with the server RP7410. After update the firmware of MP+PDHC+PDC cell 1 don't working and can't power on it. Updating firmwares works good, but cell 1 PDC have error.

HW status for Cell 1 : FAILURE DETECTED

Power status : OFF, no fault
Boot is blocked
PDH memory is not shared
RIO cable status : connected
RIO cable connection physical location : IO Chassis 1
Core cell is INVALID
Attention Led is off

PDHC status Leds : --*-

0 1 2 3
CPUs Populated *

DIMMs populated:
0 . . . 4 . . . 8 . . .12 . . .


1 1 1
VRM's 1 2 3 4 5 6 7 8 9 0 1 2
Present :
Enabled :
Pwr Good :


Cell Board DIP Switches : b'10110000
Clock type : unknown
Frequency Select reg : 0x7b
CPU Clock Select : System Backplane Clock @ 100 MHz
CPU PLL : Enabled
CPU VREF control : 1.5V
CPU Type : PA8600
CPU Speed Bits : 0x20
DIP switch settings are invalid

System Boot Rom (PDC) firmware rev 255.255
PDH controller (PDHC) firmware rev 2.02, built MON MAR 25 12:37:01 2002
IceBoy revision is 1.0

CM>FW

Number Cabinet Name Partition Handle Firmware Version Comments
------ --------- -------- --------- -------- ------------------ --------
1 0 MP 0 0 0 4.009 Slave
2 0 MP 1 0 1 4.009 Master
3 0 PDHC 0 0 256 2.002 -
4 0 PDC 0 0 320 16.011 -
5 0 PDHC 1 0 257 2.004 -
6 0 PDC 1 0 321 255.255 -


CM>SYSREV

Cabinet FPGA and Firmware revision report

System Backplane : GPM FM OSP
------- ------- -------
1.002 1.002 1.001

PCI Backplane : LPM HS
------- -------
1.002 1.000

LPM BOB DRAIN PDHC PDC
------- ------- ------- ------- -------
CELL 0 : 2.001 1.000 1.000 2.002 16.011
CELL 1 : 2.006 15.015 1.000 2.004 255.255

FPGA MP
------- -------
Master Core IO : 1.000 4.009
Slave Core IO : 1.000 4.009



and i can't power on for cell 1 - can't update firmware for PDC :( what can i do ?
6 REPLIES 6
Torsten.
Acclaimed Contributor

Re: RP7410 PDC error, CELL 1 don't power on

Are you about doing the upgrade?

Did you follow the notes step by step?



See

http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=15351&prodSeriesId=2512354&swItem=PF-CKEYMAT0605&prodNameId=86782&swEnvOID=7&swLang=13&taskId=135&mode=4&idx=0

Consider to power off cell0 and power on cell1.

Hope this helps!
Regards
Torsten.

__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.

__________________________________________________
No support by private messages. Please ask the forum!

If you feel this was helpful please click the KUDOS! thumb below!   
Aleksey Shkil_1
Occasional Advisor

Re: RP7410 PDC error, CELL 1 don't power on

yes, i do upgrade of firmwares for MP,PDHC,PDC

and now upgraded for version 6.05
MP slave and master upgrade success
PDHC cell 0 and 1 upgrade success
PDC cell 0 upgrade success
PDC cell 1 upgrade error, because i can't powered on it... CM>PE>Cell 1>ON not worked :(

tried that you write - power off cell 0 and power on cell 1 - not worked

MP:CM> pe

This command controls power enable to a hardware device.

T - Cabinet
C - Cell
D - DVD/Tape
P - IO Chassis
Select Device: c
Enter cell number: 1

The power state is OFF for Cell 1.
In what state do you want the power? (ON/OFF) ON

after look it

MP:CM> pe

This command controls power enable to a hardware device.

T - Cabinet
C - Cell
D - DVD/Tape
P - IO Chassis
Select Device: c
Enter cell number: 1

The power state is OFF for Cell 1.
In what state do you want the power? (ON/OFF)
Aleksey Shkil_1
Occasional Advisor

Re: RP7410 PDC error, CELL 1 don't power on

NEW SYSREV

MP:CM> sysrev

Cabinet FPGA and Firmware revision report

System Backplane : GPM FM OSP
------- ------- -------
1.002 1.002 1.001

PCI Backplane : LPM HS
------- -------
1.002 1.000

LPM BOB DRAIN PDHC PDC
------- ------- ------- ------- -------
CELL 0 : 2.001 1.000 1.000 2.004 17.009
CELL 1 : 2.006 15.015 1.000 2.004 255.255

FPGA MP
------- -------
Master Core IO : 1.000 4.025
Slave Core IO : 1.000 4.025
Aleksey Shkil_1
Occasional Advisor

Re: RP7410 PDC error, CELL 1 don't power on

and it is info from good worked cell 0

HW status for Cell 0 : FAILURE DETECTED

Power status : OFF, no fault
Boot is blocked
PDH memory is not shared
RIO cable status : connected
RIO cable connection physical location : IO Chassis 0
Core cell is INVALID
Attention Led is off

PDHC status Leds : --*-

0 1 2 3
CPUs Populated * *

DIMMs populated:
0 . . . 4 . . . 8 . . .12 . . .
* * * * * * * *

1 1 1
VRM's 1 2 3 4 5 6 7 8 9 0 1 2
Present : * * * * * * * * * * *
Enabled :
Pwr Good :


Cell Board DIP Switches : b'00000011
Clock type : Piranha_pll
Frequency Select reg : 0x13
CPU Clock Select : System Backplane Clock @ 130 MHz
CPU PLL : Enabled
CPU VREF control : Ground
CPU Type : PA8700
CPU Speed Bits : 0xa
Dip switch settings are valid

System Boot Rom (PDC) firmware rev 17.009
PDH controller (PDHC) firmware rev 2.04, built MON JAN 12 18:20:02 2004
IceBoy revision is 1.0


Info from cell 1

Power status : OFF, no fault
Boot is blocked
PDH memory is not shared
RIO cable status : connected
RIO cable connection physical location : IO Chassis 1
Core cell is INVALID
Attention Led is off

PDHC status Leds : --*-

0 1 2 3
CPUs Populated *

DIMMs populated:
0 . . . 4 . . . 8 . . .12 . . .


1 1 1
VRM's 1 2 3 4 5 6 7 8 9 0 1 2
Present :
Enabled :
Pwr Good :


Cell Board DIP Switches : b'10110000
Clock type : unknown
Frequency Select reg : 0x9c
CPU Clock Select : System Backplane Clock @ 100 MHz
CPU PLL : Enabled
CPU VREF control : 1.5V
CPU Type : PA8600
CPU Speed Bits : 0x30
DIP switch settings are invalid

System Boot Rom (PDC) firmware rev 255.255
PDH controller (PDHC) firmware rev 2.04, built MON JAN 12 18:20:02 2004
IceBoy revision is 1.0



So strange version of PDC's firmware
Torsten.
Acclaimed Contributor

Re: RP7410 PDC error, CELL 1 don't power on

>> System Boot Rom (PDC) firmware rev 255.255



This is normal as long as the cell is off.

Hope this helps!
Regards
Torsten.

__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.

__________________________________________________
No support by private messages. Please ask the forum!

If you feel this was helpful please click the KUDOS! thumb below!   
Aleksey Shkil_1
Occasional Advisor

Re: RP7410 PDC error, CELL 1 don't power on

WOW, great :)))
it's worked
need to upgrades all firmwares on the server
CM>OSP

and the cell 1 power ON :)