RP8400 cell automatic power off

[Joelmel Roche]

Hi,

Need help about this logs.

0 MP 0 *10 0x581008a466ff408f 0x00006b0911023817 NVRAM_BATTERY_FAIL
1 PDC 0,3,0 *4 0x2000c44076001066 0x00ffff03ff0bff74 MEM_DIMM_ERR_DEALLOCATED
1 PDC 0,3,0 *4 0x5800cc0000001060 0x00006b0911023a39 10/17/2007 02:58:57
2 PDC 0,3,0 *15 0x2000c5fb76001030 0x00ffff03ffffff94 MEM_NO_MEMORY_FOUND
2 PDC 0,3,0 *15 0x5800cd0000001030 0x00006b0911023a39 10/17/2007 02:58:57
3 PDC 0,3,0 *15 0x2000c6f07000700f 0x00ffff03ffffff94 MEM_HALT_CELL
3 PDC 0,3,0 *15 0x5800ce0000007000 0x00006b0911023a39 10/17/2007 02:58:57
4 PDC 0,3,0 *15 0x2000c7f09000001a 0x00ffff03ffffff94 BOOT_CELL_WILL_HALT
4 PDC 0,3,0 *15 0x5800cf0000000010 0x00006b0911023a39 10/17/2007 02:58:57
5 MP 0 *2 0x581008206600701f 0x00006b0911032b2f FIRMWARE_UPDATE_OP
6 MP 0 *2 0x581008206600701f 0x00006b0911033907 FIRMWARE_UPDATE_OP

MP:CM> sysrev

Cabinet FPGA and Firmware revision report

System Backplane : GPM FM OSP


------- ------- -------

1.002 1.002 1.002


PCI Backplane : LPM HS


------- -------


1.002 1.000

LPM BOB DRAIN PDHC PDC

------- ------- ------- ------- -------

CELL 0 : 2.002 1.000 1.001 2.004 17.009

CELL 1 : 2.002 1.000 1.001 2.004 17.009

CELL 2 : 2.002 1.000 1.001 2.004 17.009

CELL 3 : 2.002 1.000 1.001 2.004 17.009

FPGA MP

------- -------

Master Core IO : 2.008 4.022

Slave Core IO : 2.008 4.022


Regards,

[Prashanth.D.S]

Hi Joelmel,

Suspect the Memory Dimms have gone bad hence the system is not able to bootup would suggest you to have the dimms replaced immediately.

1 PDC 0,3,0 *4 0x2000c44076001066 0x00ffff03ff0bff74 MEM_DIMM_ERR_DEALLOCATED


FRU Type[ 7: 4]: 0x7( 7) - Memory
FRU Type Detail[ 3: 0]: 0x4( 4) - SIMM or DIMM
Level1[63:56]: Cab 0x00(0)
Level4[39:32]: Cell Slot 0x03(3)
Level6[23:16]: DIMM Slot 0x0b(11)

2 PDC 0,3,0 *15 0x2000c5fb76001030 0x00ffff03ffffff94 MEM_NO_MEMORY_FOUND

DIMM at slot 0b is gone missing now..

3 PDC 0,3,0 *15 0x2000c6f07000700f 0x00ffff03ffffff94 MEM_HALT_CELL

Description: Cell halted when fatal error was detected in memory


Best Regards,
Prashanth

[Joelmel Roche]

Hi Prashanth,

Thanks the info, might be possible for cell board 2 cant power up. In the vfp output, the status of cell-2 is "cell firmware configuration log 61" and after that auto the cell-2 down.

Thanks &regards,

[Phil uk]

Hi,

You will also need to have the Battery replaced on the GSP.

Once you have the memory issues sorted as per above, you will need to clear the PDT.
From BCH:
SER> PDT CLEAR

Phil

[tkc]

if this error is reproducible, try booting up with minimum configuration to isolate the bad hardware. try with with single cell and minimum memory in the cell board and slowly add the pcs of hardware to nail down the faulty hardware.