HPE 9000 and HPE e3000 Servers
cancel
Showing results for 
Search instead for 
Did you mean: 

Unable to HP Workstation c3750 from kan to restore ignite backup

 
sharmabas
Member

Unable to HP Workstation c3750 from kan to restore ignite backup


Unable to find Lan boot option on HP worlstation C3750 , Onboard lancard exist on server , but not showing in search output at boot console handler (BCH). Details are given below.

Main Menu: Enter command > SEA
Searching for potential boot device(s)...
This may take several minutes.
To discontinue search, press any key (termination may not be immediate).

Path Number Device Path Device Type
----------- ----------------- -----------
P0 FWSCSI.6.0 HP 36.4GMAP3367NC
P1 FWSCSI.5.0 HP 36.4GMAP3367NC


-----
Configuration Menu: Enter command > search lan install
Searching for potential boot device(s)... on Path LAN
This may take several minutes.
To discontinue search, press any key (termination may not be immediate).

Path Number Device Path Device Type
----------- ----------------- -----------
No devices found.

 


Configuration Menu: Enter command > boot lan 10.227.2.48 install
Interact with IPL (Y, N, Q)?> n
Booting...
ENTRY_INIT failed, status = -7: Nonexistent device
0x0000 0000004e 00000000 00000030 6e487f00
0x0010 00000000 00000000 00000000 00000000
0x0020 00000000 00000000 00000000 00000000
0x0030 00000000 00000000 00000000 00000000
0x0040 0000000b 00000000 000000ff 00000000
0x0050 00000000 00000000 00000000 00000000
0x0060 00000000 00000000 00600720 00000000
0x0070 00000000 00000000 00000000 00000000

Failed to initialize.

CPU 0
NOTICE: Processor self-tests have been disabled because FASTBOOT is
enabled. To enable self-tests, disable FASTBOOT with the FASTBOOT
command in the CONFIGURATION menu and reboot the system.
NOTICE: Memory has been initialized but not tested because FASTBOOT is
enabled. To test memory, disable FASTBOOT with the FASTBOOT
command in the CONFIGURATION menu and reboot the system.

1 REPLY 1
S_Logan
HPE Pro

Re: Unable to HP Workstation c3750 from kan to restore ignite backup

Hi

 

Please check the notes on Searching for bootable media

To list devices that contain bootable media, follow the directions in “accessing the boot
console handler” earlier in this chapter, and then type the following at the prompt and
press Enter:
Main Menu: Enter command > search ipl
The search command searches all buses. The search may turn up more devices than there are lines on your display. If you are using a text terminal, you may control the progress of the search from your terminal’s keyboard by performing the following steps:


• To hold the display temporarily, press Ctrl S
• To continue the display, press Ctrl Q
• To halt the search, press any other key


These flow-control commands do not work with a bit-mapped display, but such a display can show more than forty lines of text, so you are unlikely to need them.
To search for devices of just one type that actually contain bootable media, follow the directions in “accessing the boot console handler” earlier in this chapter, and then type the following at the prompt and press Enter:


Main Menu: Enter command> search ipl device_type


Where device_type is one of the following:
• fwscsi is the built-in Ultra2 Wide LVD SCSI bus.
• scsi is the built-in Fast Narrow Single-Ended SCSI bus.
• lan is all connections to the built-in LAN.

 

Main Menu: Enter command > search ipl lan

 

See the results of the above command and try to boot from the LAN

 

 Please refer the following documents for more information:

How to fix ENTRY_INIT boot failures

 

 

 

 

 

I work for HPE

Accept or Kudo