- Community Home
- >
- Servers and Operating Systems
- >
- Legacy
- >
- HPE 9000 and HPE e3000 Servers
- >
- Re: add new cell board to rp7410
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-02-2003 04:37 PM
тАО12-02-2003 04:37 PM
There is only one partition in the box.
What should I do to see new cell board in the system ?
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-02-2003 04:58 PM
тАО12-02-2003 04:58 PM
Re: add new cell board to rp7410
I'm not sure that will help, but cstm mstm or xstm(X-Windows) will show new CPU's.
From my past hardware experience,(non-cpu) the component should be visible and working right after installation and restart of the server.
Is it possible the installation is not correct? Card not properly seated, not in the right kind of slot?
SEP
Owner of ISN Corporation
http://isnamerica.com
http://hpuxconsulting.com
Sponsor: http://hpux.ws
Twitter: http://twitter.com/hpuxlinux
Founder http://newdatacloud.com
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-02-2003 05:01 PM
тАО12-02-2003 05:01 PM
Re: add new cell board to rp7410
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-02-2003 05:39 PM
тАО12-02-2003 05:39 PM
Re: add new cell board to rp7410
First make sure the existing cell have same level of firware of new cell.
Or simply after installing new cell update firmware for both cells sothat
both cells are same firmware. Once it's done you can assign the new cell
to the existing partition from BCH or through parmodify command.
After you power on please watch VFP for any error messages.
Also Chassis log (SL) for DNA...... messages.
Also make sure both cells powered on using PS command in MP.CM.
I had same problem, and I upgraded firmware and I could join the new cell
to the existing partition.
TT
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-02-2003 06:02 PM
тАО12-02-2003 06:02 PM
Re: add new cell board to rp7410
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-03-2003 06:56 AM
тАО12-03-2003 06:56 AM
Re: add new cell board to rp7410
type DU
This will give a display of what you have installed in your chassis. if there is a star under both cell boards, then the cell is recognized.
go back to hpux, and use the parstatus command to make sure the OS can see the cell board. (this command gives several pages of output, IIRC)
also, parstatus will show you which cell needs to be added to the partition.
now do a:
man parmodify
this is the command that will add the cell to your existing partition.
the command is like this:
parmodify -p 0 -a 0:base:y:ri
the number following the -a option is the cell number to be added.
-Josh
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-04-2003 02:06 AM
тАО12-04-2003 02:06 AM
SolutionThen you will need to do a reconfig reboot, (Shutdown -R now), which will cause the system to reboot and re-read the partition configuration data. The system will enter a ready for reconfig state when it resets.
The system will not actually boot until you issue the boot command from the MP's command menu (CM).
See http://www2.itrc.hp.com/service/cki/cache/200000065004691.pdf (chapter 6) for more details.