- Community Home
- >
- Servers and Operating Systems
- >
- Legacy
- >
- HPE 9000 and HPE e3000 Servers
- >
- chars L2000 & L3000
HPE 9000 and HPE e3000 Servers
1748089
Members
5031
Online
108758
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Go to solution
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-22-2004 10:53 PM
тАО02-22-2004 10:53 PM
Hi,
I would like to put this targets in the servers:
L2000: 1 GB Ethernet and 1 DAT (inside or outside)
L3000: 1 DAT (inside or outside), (better I could put it inside the server)
Is it possible?, How could I known all them?
Thanks a lot of!
Carmen.
I would like to put this targets in the servers:
L2000: 1 GB Ethernet and 1 DAT (inside or outside)
L3000: 1 DAT (inside or outside), (better I could put it inside the server)
Is it possible?, How could I known all them?
Thanks a lot of!
Carmen.
Users are not too bad ;-)
Solved! Go to Solution.
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-22-2004 11:04 PM
тАО02-22-2004 11:04 PM
Solution
Hi Carmen,
For the L2000
A4926A LAN adapter - 1000Base-SX PCI Gigabit Ethernet LAN adapter - Supports all PCI bus configurations
A4929A LAN adapter - 1000Base-T PCI Gigabit Ethernet LAN adapter - Supports all PCI bus configurations
A5558A DDS-3 (DAT) Tape Drive - 12GB (24GB with Data Compression) - 5.25-inch, Single Ended SCSI-2 Interface
The can also be used in the L3000
Regards,
Robert-Jan
For the L2000
A4926A LAN adapter - 1000Base-SX PCI Gigabit Ethernet LAN adapter - Supports all PCI bus configurations
A4929A LAN adapter - 1000Base-T PCI Gigabit Ethernet LAN adapter - Supports all PCI bus configurations
A5558A DDS-3 (DAT) Tape Drive - 12GB (24GB with Data Compression) - 5.25-inch, Single Ended SCSI-2 Interface
The can also be used in the L3000
Regards,
Robert-Jan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-22-2004 11:13 PM
тАО02-22-2004 11:13 PM
Re: chars L2000 & L3000
The L-class servers on the rear side have 12 PCI slots with which the first slot is the Core I/O slot which can be used to connect a DAT drive.
if you are using the Rack type then there is a Rack mounted adapter behind where the DAT drive can be fixed internally.
With these PCI slots you can connect the gigabit adapter.
check the link for the compatible gigabit adapters for rp5400
http://www.hp.com/products1/unixserverconnectivity/adapters/ethernet/specifications/gigabit_ethernet_specs.html
Also check the PCI installation chapter of this document.THis has all the required
http://docs.hp.com/hpux/onlinedocs/A5191-96022/A5191-96022.html
if you are using the Rack type then there is a Rack mounted adapter behind where the DAT drive can be fixed internally.
With these PCI slots you can connect the gigabit adapter.
check the link for the compatible gigabit adapters for rp5400
http://www.hp.com/products1/unixserverconnectivity/adapters/ethernet/specifications/gigabit_ethernet_specs.html
Also check the PCI installation chapter of this document.THis has all the required
http://docs.hp.com/hpux/onlinedocs/A5191-96022/A5191-96022.html
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP