- Community Home
- >
- Servers and Operating Systems
- >
- Legacy
- >
- HPE 9000 and HPE e3000 Servers
- >
- Re: reset the interface’s IP address from the MP c...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-16-2006 08:06 AM
01-16-2006 08:06 AM
please suggest me the steps.
thanks
bunty
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-16-2006 08:16 AM
01-16-2006 08:16 AM
SolutionIf you mean the MP - then yes, from the Command Menu, CM, type HE to get a list of commands...LC to configure Lan Cards.
Rgds...Geoff
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-16-2006 08:17 AM
01-16-2006 08:17 AM
Re: reset the interface’s IP address from the MP console
The only LAN interface the MP can access is its own.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-16-2006 08:38 AM
01-16-2006 08:38 AM
Re: reset the interface’s IP address from the MP console
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-16-2006 08:42 AM
01-16-2006 08:42 AM
Re: reset the interface’s IP address from the MP console
Then either manually re-configure lan0 or use sam.
Rgds...Geoff
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-16-2006 06:52 PM
01-16-2006 06:52 PM
Re: reset the interface’s IP address from the MP console
If you are planning to change the IP address of lan0, one of the possible 2 ways is to connect to MP via LAN and then go to console.
From there, modify the IP address of LAN0. the other possible way is to access the local console (Through dumb terminal or laptop) and perform the same action.
Doing so will not disconnect your session, but will disconnect users who have already logged-in through telnet or rlogin.
In your first post you are asking about "reset". If you want to reset the LAN0, then the above reply is still applicable.
Hope this helps.
With regards,
Mohan.