- Community Home
- >
- Servers and Operating Systems
- >
- Legacy
- >
- HPE 9000 and HPE e3000 Servers
- >
- Re: rp 4440 - flashing RED on System LED
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-12-2005 11:17 PM
тАО10-12-2005 11:17 PM
rp 4440 - flashing RED on System LED
We have 2 rp 4440 servers. On both servers the system LED is flashing RED. But the system is running without any problem so far.
Is it a concern? or h/w a flaw?
Is there any solution for that.
The firmware details.
MP FW : E.02.29
BMC FW : 02.37
System FW : 44.21
I also attach the logs in the file.
Pl. help me in resolving this issue. Thanks in advance
- Sundar
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-13-2005 12:01 AM
тАО10-13-2005 12:01 AM
Re: rp 4440 - flashing RED on System LED
Check Cheryl's answer in this thread.
http://forums1.itrc.hp.com/service/forums/questionanswer.do?threadId=753066&admit=-682735245+1129204839885+28353475
Best regards,
Robert-Jan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-13-2005 12:08 AM
тАО10-13-2005 12:08 AM
Re: rp 4440 - flashing RED on System LED
Hi Sundar,
on GSP, what are the log errors, if you type : sl ( show log) then e.
Ziad
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-13-2005 12:16 AM
тАО10-13-2005 12:16 AM
Re: rp 4440 - flashing RED on System LED
Sundar add on.
latest patch below, there is also a patch for 11.23
Patch Name: PHSS_33088
Patch Description: s700_800 11.11 rp4440/rp4410 PDC45.11/BMC03.49/MPE.03.15 FW
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-13-2005 05:00 AM
тАО10-13-2005 05:00 AM
Re: rp 4440 - flashing RED on System LED
Robert ..
I tried downloading PHSS_33088. It shows me the following error.
* Beginning Analysis Phase.
* Source: hpux:/scratch/FW_patches/PHSS_33088.depot
* Target: micqa1:/
* Target logfile: hpux:/var/adm/sw/swagent.log
* Reading source for product information.
* Reading source for file information.
NOTE: The device file for the primary boot disk as reported
by setboot(1M), , does not match the FIRST one listed
in the file /stand/bootconf, /dev/dsk/c4t0d1. PHSS_33088 will be
excluded from installation. Please correct the /stand/bootconf
file and then install PHSS_33088.
NOTE: The "checkinstall" script for "PHSS_33088.KERN-RUN" gave an
"exclude" return (exit code "3"). The script location was
"/var/tmp/BAAa15017/catalog/PHSS_33088/KERN-RUN/checkinstall".
NOTE: This software will be excluded from further processing.
* Executing preDSA command.
Please note that I am booting the system from a SAN path. And the /stand/bootconf file is correct.
Pl. send your suggestions.
Regards
- Sundar
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-13-2005 06:17 AM
тАО10-13-2005 06:17 AM
Re: rp 4440 - flashing RED on System LED
It seems that the disk is not listed as the "FIRST" disk in your /stand/bootconf file. It has to be the first disk in that file to have successful patch installation. Not only this, there are other requirements as well given under "Special Installation Instruction". Refer them first.
Identify your current disk using ioscan and put it as the FIRST entry in bootconf. Similarly set the autoboot as well using
#setboot -b on before starting patch installation.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-14-2005 04:47 AM
тАО10-14-2005 04:47 AM
Re: rp 4440 - flashing RED on System LED
I tried in the following sequence.
i) ran ioscan -func disk. took the disk it shows as "boot disk". say /dev/dsk/c4t6d0.
ii) ran #lifcp /dev/rdsk/c4t6d0:AUTO /tmp/auto
iii) The /tmp/auto file showed lines
srvrflash & hpux
iv) I restored the boot path file using mkboot -a "hpux"
v) I also changed the /stand/bootconf file as shown by iscan.
vi) then i tried reinstalling the patch.
No sucess. The same error. But when i rebooted, the system was not able to boot. I tried booting from the previous h/w path.
This is the problem. Can you explore more on this Please?
Regards
G.Sundar
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-15-2005 01:35 AM
тАО10-15-2005 01:35 AM
Re: rp 4440 - flashing RED on System LED
Hope this helps,
Robert-Jan