- Community Home
- >
- Servers and Operating Systems
- >
- Legacy
- >
- HPE 9000 and HPE e3000 Servers
- >
- Re: rp2430 remind fan failure,could not fix after ...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-05-2010 12:40 AM
11-05-2010 12:40 AM
rp2430 remind fan failure,could not fix after replacing fan assembly.
I've got an rp2430 panic, os reminded that there was fan failing, and ps at GSP> told fan 1 was in failure status, then after about 1 minute, the server power off itself. Then I cut off the power and then power on the server again, everything was ok and the os could boot, then after several minutes, it failed again, telling fan 1 failure again. Then I replace fan assembly, the same situation happened again.
what could be the cause of this issue? It seemed that fan was not failed in fact, would it be caused by the system board?
attachment were shortcut of the screen when the failure happened.
thanks a lot!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-05-2010 12:42 AM
11-05-2010 12:42 AM
Re: rp2430 remind fan failure,could not fix after replacing fan assembly.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-05-2010 01:20 AM
11-05-2010 01:20 AM
Re: rp2430 remind fan failure,could not fix after replacing fan assembly.
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-05-2010 02:03 AM
11-05-2010 02:03 AM
Re: rp2430 remind fan failure,could not fix after replacing fan assembly.
I replace part A5570-00001, any comment about this replacement?
regards
stephen
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-05-2010 02:20 AM
11-05-2010 02:20 AM
Re: rp2430 remind fan failure,could not fix after replacing fan assembly.
If the system goes off, what is the GSP's "ps" command telling?
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-05-2010 03:00 AM
11-05-2010 03:00 AM
Re: rp2430 remind fan failure,could not fix after replacing fan assembly.
PS
Power Monitor Status:
Firmware Revision : 9
System Power state: On Power Switch : On
Temperature : Normal Selected fan state: Normal
Power supplies | Fan
# State Type | States
-----------------------------------------------------------
0 Normal Type 0 | Normal
1 - - | Normal
2 - - | Normal
3 - - | Normal
4 - - | Normal
then after power went down.
Power Monitor Status:
Firmware Revision : 9
System Power state: On Power Switch : On
Temperature : Normal Selected fan state: Normal
Power supplies | Fan
# State Type | States
-----------------------------------------------------------
0 Normal Type 0 | Failure
1 - - | Normal
2 - - | Normal
3 - - | Normal
4 - - | Normal
I replace two fan assembly, which turned out to be in vain. so I doubted about it.
regards
stephen
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-05-2010 03:07 AM
11-05-2010 03:07 AM
Re: rp2430 remind fan failure,could not fix after replacing fan assembly.
Power Monitor Status:
Firmware Revision : 9
System Power state: OFF Power Switch : On
Temperature : Normal Selected fan state: Failure
Power supplies | Fan
# State Type | States
-----------------------------------------------------------
0 Normal Type 0 | Failure
1 - - | Normal
2 - - | Normal
3 - - | Normal
4 - - | Normal
after power went off
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-08-2010 04:47 PM
11-08-2010 04:47 PM
Re: rp2430 remind fan failure,could not fix after replacing fan assembly.
http://www13.itrc.hp.com/service/cki/docDisplay.do?hpweb_printable=true&docId=emr_na-c00927374&docLocale=en
Rgds,