HPE 9000 and HPE e3000 Servers
cancel
Showing results for 
Search instead for 
Did you mean: 

rp5430 boot problem

 
anis_3
Occasional Advisor

rp5430 boot problem

After a disk between two identical rp4530 the first one booted correctly but the second failed
Could someone help me to localize where is the problem?

here the errors :



*****************************************

************ EARLY BOOT VFP *************
End of early boot detected
*****************************************

Firmware Version 43.43

Duplex Console IO Dependent Code (IODC) revision 1

------------------------------------------------------------------------------
(c) Copyright 1995-2002, Hewlett-Packard Company, All rights reserved
------------------------------------------------------------------------------

Processor Speed State CoProcessor State Cache Size
Number State Inst Data
--------- -------- --------------------- ----------------- ------------
0 750 MHz Active Functional 750 KB 1.5 MB
2 750 MHz Idle Functional 750 KB 1.5 MB

Central Bus Speed (in MHz) : 133
Available Memory : 4194304 KB
Good Memory Required : 31560 KB

Primary boot path: 0/0/1/1.0
Alternate boot path: 0/0/2/0.0
Console path: 0/0/4/1.0
Keyboard path: 0/0/4/0.0


Processor is booting from first available device.

To discontinue, press any key within 10 seconds.

10 seconds expired.
Proceeding...

Trying Primary Boot Path
------------------------
Booting...
Boot IO Dependent Code (IODC) revision 1


HARD Booted.

ISL Revision A.00.43 Apr 12, 2000

ISL booting hpux -lq (;0)/stand/vmunix

Boot
: disk(0/0/1/1.0.0.0.0.0.0;0)/stand/vmunix
10256384 + 1847296 + 1712304 start 0x205868




alloc_pdc_pages: Relocating PDC from 0xffff800000 to 0x7fa00000.
gate64: sysvec_vaddr = 0xc0002000 for 2 pages
NOTICE: autofs_link(): File system was registered at index 3.
NOTICE: cachefs_link(): File system was registered at index 5.
NOTICE: nfs3_link(): File system was registered at index 6.

System Console is on the Built-In Serial Interface
Logical volume 64, 0x3 configured as ROOT
Logical volume 64, 0x2 configured as SWAP
Logical volume 64, 0x2 configured as DUMP
Swap device table: (start & size given in 512-byte blocks)
entry 0 - major is 64, minor is 0x2; start = 0, size = 16777216
Starting the STREAMS daemons-phase 1

Checking root file system.
Root check done.

************* SYSTEM ALERT **************
SYSTEM NAME: webconsole
DATE: 02/01/2007 TIME: 20:44:02
ALERT LEVEL: 12 = Software failure

REASON FOR ALERT
SOURCE: 1 = processor
SOURCE DETAIL: 1 = processor general SOURCE ID: 0
PROBLEM DETAIL: 0 = no problem detail

LEDs: RUN ATTENTION FAULT REMOTE POWER
FLASH FLASH FLASH ON ON
LED State: Unexpected Reboot. Running non-OS code. Non-critical error detected.
Check Chassis and Console Logs for error messages.
3 REPLIES 3
Luk Vandenbussche
Honored Contributor
anis_3
Occasional Advisor

Re: rp5430 boot problem

in GSP mode within a 5430 how to boot in maintenance mode ?

Regards
goldboy
Trusted Contributor

Re: rp5430 boot problem

anis,
stop the system at the BCH.
and boot from your primary boot disk.
choose to interact with IPL.

and then:

ISL>hpux -lm

that will boot you up to maintenence mode.

"Life is what you make out of them!"