- Community Home
- >
- Servers and Operating Systems
- >
- Legacy
- >
- HPE 9000 and HPE e3000 Servers
- >
- Re: rp7420 - MP access after powerfailure
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-01-2008 09:06 AM
тАО07-01-2008 09:06 AM
rp7420 - MP access after powerfailure
after power failure we are not able to connect to MP. We reset it then we were able to connect but vfp shows BOOT_MONARCH_DONE_CHECKING_SLAVE.
after disconnecting power for a while and reconnecting we were able to get to the MP again but this time vfp shows no partition configuration
Any ideas?
Thanks in advance
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-01-2008 01:25 PM
тАО07-01-2008 01:25 PM
Re: rp7420 - MP access after powerfailure
Sounds like it is just broke.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-02-2008 09:20 AM
тАО07-02-2008 09:20 AM
Re: rp7420 - MP access after powerfailure
any ideas?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-02-2008 06:27 PM
тАО07-02-2008 06:27 PM
Re: rp7420 - MP access after powerfailure
regards,
Sandy
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-03-2008 06:35 PM
тАО07-03-2008 06:35 PM
Re: rp7420 - MP access after powerfailure
Why were you trying to execute xd?? normally it is used to upgrade the firmware version of the MP? Were you trying to do that and it hanged in between??
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-04-2008 12:39 AM
тАО07-04-2008 12:39 AM
Re: rp7420 - MP access after powerfailure
i think you have a bad mp.
Usually an rp7420 would have 2nd mp.
Try access that and check again whether the config is still intact.
Go to CM -> XD and run all options. This is to check whether the mP is OK.
By the way, mridul. I maybe wrong but last time i upgrade the GSP firmware, i had to run XU and not XD. Pls correct me. Thanks.
Rgds
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-04-2008 05:32 PM
тАО07-04-2008 05:32 PM
Re: rp7420 - MP access after powerfailure
replaced the MP and it is working fine
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-04-2008 05:34 PM
тАО07-04-2008 05:34 PM