- Community Home
- >
- Servers and Operating Systems
- >
- Legacy
- >
- HPE 9000 and HPE e3000 Servers
- >
- Re: unable to boot a v2500 running 11.11
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-08-2009 03:11 AM
тАО10-08-2009 03:11 AM
unable to boot a v2500 running 11.11
: disc(4/1/0.6.0;0)/stand/vmunix
10633216 + 1945600 + 10575104 start 0x1fd368
no hpa_module_entry for f00001d5
get_spp_path_entry:obp_paths failed 2
any ideas?
thank you in advance
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-08-2009 04:18 AM
тАО10-08-2009 04:18 AM
Re: unable to boot a v2500 running 11.11
Has this failed in service or is it a new os install ?
>get_spp_path_entry:obp_paths failed 2
This may indicate a hardware error affecting messaging to console system from the system backplane .
mike
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-08-2009 05:03 AM
тАО10-08-2009 05:03 AM
Re: unable to boot a v2500 running 11.11
we are connected directly to the console
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-08-2009 05:21 AM
тАО10-08-2009 05:21 AM
Re: unable to boot a v2500 running 11.11
what PDC firmware version is running on this system?
if you are on the console, got to forth mode (I think the shortcut was FM ) and issue printenv
post results here..
HTH
Duncan
I am an HPE Employee
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-08-2009 05:25 AM
тАО10-08-2009 05:25 AM
Re: unable to boot a v2500 running 11.11
PDC_ENTRY version 4.3.3.0
POST Revision: 5.3.0.0
OBP Release 4.3.3, compiled 00/10/11 (3)
SPP_PDC (64-bit) Release 3.2 (01/08/01)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-08-2009 06:36 AM
тАО10-08-2009 06:36 AM
Re: unable to boot a v2500 running 11.11
I can't remember the exact name of the control board but it sits on the service network between the test station (console) and the centre plane and manages all the hardware and service access between the v class itself and the test station. It does all the enviroment and fault monitoring and relays messages back to the console, if there is some fault there or if it can't communicate properly, the system will struggle to come up.
I am fairly sure that 3.2 is the correct level to run hp-ux 11.11
Since it has failed while running, I would be inclined to get the hardware looked at first .
I hope this is of some help
Mike
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-09-2009 06:14 PM
тАО10-09-2009 06:14 PM
Re: unable to boot a v2500 running 11.11
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-09-2009 08:55 PM
тАО10-09-2009 08:55 PM
Re: unable to boot a v2500 running 11.11
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-09-2009 09:10 PM
тАО10-09-2009 09:10 PM
Re: unable to boot a v2500 running 11.11
no hpa_module_entry for f00001d5
get_spp_path_entry:obp_paths failed 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-09-2009 10:37 PM
тАО10-09-2009 10:37 PM
Re: unable to boot a v2500 running 11.11
Did you try booting from CD/DVD (probably that will also fail).
What I feel is that you might need to upgrade PDC firmware to 5.3.2 at least.
Regds..