- Community Home
- >
- Servers and Operating Systems
- >
- HPE BladeSystem
- >
- BladeSystem - General
- >
- HP storage blade D2200sb boot question.
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-23-2012 08:30 AM
02-23-2012 08:30 AM
HP storage blade D2200sb boot question.
Irit had a customer question on the D2200sb storage blade:
*****************
I have a customer, who has an issue with the HP storage blade D2200sb:
_________________________________________________________________________________________________________________________________________________
I have host blade connected with storage blade D2200sb (e.g.: bay1 and bay2),
When I’m trying to install Linux OS on the host blade, I found that when OS scan the bus, the storage blade get to be mapped first and only then the local drives on the host,
e.g.:
Storage blade has 4 drives in Raid1/0 – (2TB)
Local drives are in Riad1 – (146GB)
When we using our automatic OS installation, this is probably the reason why the OS installed by default on the storage blade rather than the local drives (which we desire to install on local drives rather than on storage blade)
My question: Is there a way to set the bus scan of the OS (maybe via BIOS settings) in a way that the local hard drives will get to be the first to be scanned?
(So local drives will get /cciss/c0d0)
*************************
Help from Dave:
*********************
They should be able to set the internal Embedded array to boot first by changing the Boot Controller order in the ROMBIOS.
It would look something like this:
******************
I hope that helps. Any other comments or suggestions for Irit?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-09-2017 06:43 PM
03-09-2017 06:43 PM
Re: HP storage blade D2200sb boot question.
How do you do this on G9 with UEFI enabled?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-10-2017 01:29 AM
03-10-2017 01:29 AM
Re: HP storage blade D2200sb boot question.
This storage blade is not supported by Gen9 servers.
Consider to open a new thread.
Is "how to configure boot order in UEFI" the question?
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!