- Community Home
- >
- Servers and Operating Systems
- >
- HPE BladeSystem
- >
- BladeSystem - General
- >
- Re: Update SB40C blade in c3000 enclosure
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-05-2013 05:35 AM
тАО07-05-2013 05:35 AM
Update SB40C blade in c3000 enclosure
I have a customer with a c3000 enclosure with OA firmware 3.55 and I am recommending that they update to 3.71. I notice that they have an SB40c storage blade also that is at fw version 1.20. Where do I find the recommended version for that blade that is compatible with 3.71 OA firmware and how do we go about updating the SB40c blade?
- Tags:
- firmware update
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-05-2013 12:08 PM
тАО07-05-2013 12:08 PM
Re: Update SB40C blade in c3000 enclosure
I found the following fromt the SB40c support page:
Select the "Guided Troubleshooting" section and you will see a section about updating firmware:
----------------------------------------------
SB40c Storage Blade firmware is already embedded in the OA firmware code. From OA CLI run the following command:
>SHOW UPDATE
A table showing components, current and new firmware versions will be displayed.
To update the firmware on SB40c Storage Blade, run the command
>UPDATE DEVICE XX
Where XX stands for location.
---------------------------------------------
Basically, you perform the OA update and then run the SHOW UPDATE and UPDATE DEVICE commands from the OA CLI to update the Storage Blade (as well as any Pass Through modules you may have).
Also, note that the SB40c has an embedded P400 controller that you can update via the partner blade OS.
-Bob
Was this helpful? Like this post by giving me a thumbs up below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-05-2013 01:13 PM
тАО07-05-2013 01:13 PM
Re: Update SB40C blade in c3000 enclosure
Thank you for your guidance. It sounds easy enough, won't be able to tell until I am at the customer to do the work. I am also still unsure about the p400 controller that will get updated from the partner blade. Thank you gor pointing in the right place for information.