- Community Home
- >
- Storage
- >
- Midrange and Enterprise Storage
- >
- HPE EVA Storage
- >
- Re: Activate all paths for a LUN
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-14-2009 10:54 PM
тАО06-14-2009 10:54 PM
Activate all paths for a LUN
I have the following output from the SCSIMGR command shows the paths I have and status for each one of them
***********************************************
prod2# scsimgr lun_map -D /dev/rdisk/disk29
LUN PATH INFORMATION FOR LUN : /dev/rdisk/disk29
Total number of LUN paths = 4
World Wide Identifier(WWID) = 0x600508b40006cbf10001600000520000
LUN path : lunpath44
Class = lunpath
Instance = 44
Hardware path = 0/0/12/1/0/4/0.0x50001fe15010d278.0x400300000000
0000
SCSI transport protocol = fibre_channel
State = ACTIVE
Last Open or Close state = ACTIVE
LUN path : lunpath45
Class = lunpath
Instance = 45
Hardware path = 0/0/12/1/0/4/0.0x50001fe15010d27c.0x400300000000
0000
SCSI transport protocol = fibre_channel
State = STANDBY
Last Open or Close state = STANDBY
LUN path : lunpath43
Class = lunpath
Instance = 43
Hardware path = 0/0/14/1/0/4/0.0x50001fe15010d279.0x400300000000
0000
SCSI transport protocol = fibre_channel
State = ACTIVE
Last Open or Close state = ACTIVE
LUN path : lunpath46
Class = lunpath
Instance = 46
Hardware path = 0/0/14/1/0/4/0.0x50001fe15010d27d.0x400300000000
0000
SCSI transport protocol = fibre_channel
State = STANDBY
Last Open or Close state = STANDBY
***********************************************
It is clear that two of them standby and not in use??
Please guys help me to find out how can I make all of them active in order to enhance performance??
Thanx in advance
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-14-2009 11:34 PM
тАО06-14-2009 11:34 PM
Re: Activate all paths for a LUN
50001fe15010d278 = Controller A FP2
50001fe15010d27c = Controller B FP2
50001fe15010d279 = Controller A FP1
50001fe15010d27d = Controller B FP1
As you can see, the active paths are through the two ports on controller A. This is the normal situation with firmware 3.x, which is Active/Passive.
Paths through controller B are only activated if there's a failure on paths to controller A.
You need firmware 4.x to convert the EVA to Active/Active mode, like the recent models.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-15-2009 02:10 AM
тАО06-15-2009 02:10 AM
Re: Activate all paths for a LUN
Actully we have 6100 EVA and with 6.1 firmware version ...
so would you help me to change the EVA mode from Active/Passive to Active/Active??
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-15-2009 04:34 AM
тАО06-15-2009 04:34 AM
Re: Activate all paths for a LUN
What operating system is this? Maybe you need to configure something on the multipath software.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-16-2009 02:41 AM
тАО06-16-2009 02:41 AM
Re: Activate all paths for a LUN
What is the version of OS you are using. If you are using HP UX 11.23, 11.11 then you can use HP Secure Path.
You have to install SecurePath which supports Active-Active disk arrays.
While installing secure path version 3 and above it will prompt for selecting the support for Active/Active or active/passive disk arrays.
Once you install SecurePath by selecting Active/Active. You can run the command autopath with options like discover, display etc.....
And can view the multiple path and it's Virtual path.
Autopath is also having the option to set LoabBalancing policy if you give Load balancing policy as round robin all the path to the lun will active and do a I/O load balancing.
Please go through the document c00248499.pdf in HP site for more info regarding SecurePath.
Thanks and regards,
manoj K
Manoj K
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-16-2009 02:47 AM
тАО06-16-2009 02:47 AM
Re: Activate all paths for a LUN
I am using HP-UX v3 , so there is no need for Secure Path to be installed.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-16-2009 03:37 AM
тАО06-16-2009 03:37 AM
Re: Activate all paths for a LUN
For EVA6100 and HP-UX 11-23 or earlier you should be using HP SP V3.0f.
If you have V3.0c then that was for VCS V3.xxx
Easy way to check and to sort out your load balencing is to enter "autopath" rtn from the prompt and you will see the options you have.
For HP-UX 11-31 then it is native.
Mark...