HPE EVA Storage

How do I factory default AA979A 2/8V SAN switch

 
SOLVED
Go to solution

How do I factory default AA979A 2/8V SAN switch

I bought this AA979A used and the login and password is not set the default admin/password. I try to enter the boot interface console and I can't find how to reset the login name. I have already tried configDefault.

Thanks for any help
4 REPLIES 4
Gerardo Arceri
Trusted Contributor
Solution

Re: How do I factory default AA979A 2/8V SAN switch

I've googled around and came thru this:
(Remember that this switch Runs Brocade's Fabric OS)
http://community.brocade.com/docs/DOC-1644

Don't know if it will be useful.
Also there is a Brocade Password Reset utility that requires a serial cable, as described on
http://forums.sun.com/thread.jspa?threadID=5093675.
The links to the password recovery utility can be found at
http://community.brocade.com/thread/1527?start=15&tstart=0

hope it helps
Johan Guldmyr
Honored Contributor

Re: How do I factory default AA979A 2/8V SAN switch

Default password might be "fibranne". Maybe that works?

Re: How do I factory default AA979A 2/8V SAN switch

these step help me reset the switch login/password.

AA979A HP SAN switch
Silkworm3250

RESET PASSWORD AND LOGIN NAME


stop before it boots
select number 3
> printenv

AutoLoad=yes
ENET_MAC=00051E342EC7
InitTest=MEM()
LoadIdentifiers=Fabric Operating System;Fabric Operating System
OSBooted=MEM()0xF0000000
OSLoadOptions=quiet;quiet
OSLoader=MEM()0xF0000000;MEM()0xF0800000
OSRootPartition=hda1;hda2
SkipWatchdog=yes

> boot MEM()0xF0000000 -s
Booting "Manually selected OS" image.
Entry point at 0x00800000 ...

Linux/PPC load:
BootROM command line: -s
Uncompressing Linux...done.
Now booting the kernel
Linux version 2.4.19 (swrel@sierra) (gcc version 2.95.3 20010112 (prerelease)) #1 Wed Jul 26 00:15:16 PDT 2006
On node 0 totalpages: 32768
zone(0): 32768 pages.
zone (0): min(255), low(1275), high (2040)
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: -s
Set up jiffies counter to wrap in 0 seconds.
Calibrating FIT timer... running at 1526 Hz. [TSR_FP=2]
Calibrating delay loop... 199.88 BogoMIPS
Memory: 123856k available (1848k kernel code, 1124k data, 76k init, 0k highmem)
Dentry cache hash table entries: 16384 (order: 5, 131072 bytes)
Inode cache hash table entries: 8192 (order: 4, 65536 bytes)
Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
Buffer-cache hash table entries: 8192 (order: 3, 32768 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
OCP uart ver 1.6.1 init complete
Starting kswapd
Journalled Block Device driver loaded
SGI XFS with no debug enabled
i2c-core.o: i2c core module version 2.6.3 (20020322)
i2c-dev.o: i2c /dev entries driver module version 2.6.3 (20020322)
i2c-proc.o version 2.6.3 (20020322)
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0xef600400 (irq = 1) is a 16550A
ttyS01 at 0xef600300 (irq = 0) is a 16550A
PPC 405 watchdog driver v0.5. (Timer driven)
SWBD Platform Driver v1.0: [type 27, rev 3].
Config Silkworm
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
cpld_ide_init_hwif_ports: dp=0, cp=0, hw=c0487f08
silkworm.c: read cpld_data (offset 0xc100001f), 0x00
Silkworm CPLD ATA interface configured [CPLD version 0]
cpld_ide_init_hwif_ports: dp=0, cp=0, hw=c0487f08
cpld_ide_init_hwif_ports: dp=0, cp=0, hw=c0487f08
cpld_ide_init_hwif_ports: dp=0, cp=0, hw=c0487f08
cpld_ide_init_hwif_ports: dp=0, cp=0, hw=c0487f08
cpld_ide_init_hwif_ports: dp=0, cp=0, hw=c0487f08
cpld_ide_init_hwif_ports: dp=0, cp=0, hw=c0487f08
cpld_ide_init_hwif_ports: dp=0, cp=0, hw=c0487f08
hda: TOSHIBA THNCF256MBA, ATA DISK drive
ide0 at 0xe10021f0-0xe10021f7,0xe10023f6 on irq 30
hda: 500736 sectors (256 MB) w/2KiB Cache, CHS=978/16/32
Partition check:
hda: hda1 hda2
RAMDISK driver initialized: 16 RAM disks of 6144K size 1024 blocksize
loop: loaded (max 8 devices)
eth0: Phy @ 0x1, type BCM5221 (0x004061e4)
eth0: IBM OCP 10/100 Mbps ethernet: EMAC0, MAC 00:05:1e:34:2e:c7
eth0: Tx/Rx Interrupt mitigation (1500 pps)
ATA polled-mode panic dumper on char-major-252.
silkworm: Using SWBD27 flash configuration
Creating 2 MTD partitions on "Boot flash":
0x00000000-0x00010000 : "bootenv: boot environment"
0x00010000-0x00080000 : "prom: boot prom"
Creating 5 MTD partitions on "User flash":
0x00000000-0x01000000 : "Entire user flash"
0x00000000-0x00400000 : "kern0: kernel and initrd (1)"
0x00800000-0x00c00000 : "kern1: kernel and initrd (2)"
0x00400000-0x00800000 : "dump0: log data (1)"
0x00c00000-0x01000000 : "dump1: log data (2)"
Creating 2 MTD partitions on "Boot flash":
0x00000000-0x00010000 : "bootenv0s: boot environment"
0x00010000-0x00020000 : "bootenv1s: boot environment"
Silkworm crash dump logger using dump0: log data (1)
mtdchar: write-caching enabled
IBM On-chip iic (i2c) algorithm module 2002.30.04
iic_ibmocp_init: IBM on-chip iic adapter module
M41T11 Real-time-clock Driver v1.1
m41t11: Called to probe for bus IIC-0
m41t11: I2C Real-Time-Clock detected on iic0 addr 0x68
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP: Hash tables configured (established 8192 bind 8192)
Linux IP multicast router 0.06 plus PIM-SM
ip_tables: (C) 2000-2002 Netfilter core team
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: ext2 filesystem found at block 0
RAMDISK: Loading 2603 blocks [1 disk] into ram disk... done.
Freeing initrd memory: 2603k freed
VFS: Mounted root (ext2 filesystem).
Attempting to find a root file system on hda1...
hda: hda1 hda2
hda: hda1 hda2
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,1), internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
hda: hda1 hda2
hda: hda1 hda2
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Trying to move old root to /initrd ... okay
Freeing unused kernel memory: 76k init
INIT: version 2.78 booting
#
# mount -o remount,rw,noatime /
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,1), internal journal
# mount /dev/hda2 /mnt
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,2), internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
#
# /sbin/passwddefault
modprobe: modprobe: Can't locate module char-major-244
modprobe: modprobe: Can't locate module char-major-245
passwdCfg: fabosInit failed with 2
All account passwords have been successfully set to factory default.
#
# reboot -f

login: admin
password: password
set all password to (password)

Re: How do I factory default AA979A 2/8V SAN switch

hope this helps