- Community Home
- >
- Storage
- >
- Midrange and Enterprise Storage
- >
- HPE EVA Storage
- >
- Re: MSA 1000 / MSA Embedded 2/8 Switch
HPE EVA Storage
1752701
Members
6199
Online
108789
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-23-2010 08:55 AM
тАО02-23-2010 08:55 AM
MSA 1000 / MSA Embedded 2/8 Switch
I have an existing setup comprising of the following:
MSA1000
2/8 Switch
2x DL385 server each connected with fiber to ports 1 & 2 of the switch.
I have a new Windows server which I want to add "server 3" and have completed the following:
HBA installed and connected to Port3 on switch.
New connection added to MSA1000 via Cli entering the wwpn and friendly server name.
7 new disks configured in Raid 5
SSP set so that "server" 3 can access disks.
The bit I am stuck on is zoning on the 2/8 switch, we have an existing single zone with the other 2 servers specified and the MSA1000. Within zone administration (connecting via the web to the san switch). I attempt to add Port 3 which is the new server and I get an error in the log. Am I following the correct process?
MSA1000
2/8 Switch
2x DL385 server each connected with fiber to ports 1 & 2 of the switch.
I have a new Windows server which I want to add "server 3" and have completed the following:
HBA installed and connected to Port3 on switch.
New connection added to MSA1000 via Cli entering the wwpn and friendly server name.
7 new disks configured in Raid 5
SSP set so that "server" 3 can access disks.
The bit I am stuck on is zoning on the 2/8 switch, we have an existing single zone with the other 2 servers specified and the MSA1000. Within zone administration (connecting via the web to the san switch). I attempt to add Port 3 which is the new server and I get an error in the log. Am I following the correct process?
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-23-2010 09:14 AM
тАО02-23-2010 09:14 AM
Re: MSA 1000 / MSA Embedded 2/8 Switch
Mark,
If you can write the error details here would give a hint what's going on wrong here.
Also, if you can show the current zone config setting.
The procedure to enter a third port into zone is simple.
Add the port3 to existing zone where other 2 server and MSA are already in. Then enable the config (config name will depend on your environment and make sure there is only one config file, if you have more than one then better be careful which config you are enabling).
Hope that helps.
If you can write the error details here would give a hint what's going on wrong here.
Also, if you can show the current zone config setting.
The procedure to enter a third port into zone is simple.
Add the port3 to existing zone where other 2 server and MSA are already in. Then enable the config (config name will depend on your environment and make sure there is only one config file, if you have more than one then better be careful which config you are enabling).
Hope that helps.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-23-2010 09:56 AM
тАО02-23-2010 09:56 AM
Re: MSA 1000 / MSA Embedded 2/8 Switch
I re-tried the process and it has now worked. I can now successfully see my disks from the new server.
Many thanks for your prompt reply ... much appreciated.
Many thanks for your prompt reply ... much appreciated.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP