- Community Home
- >
- Storage
- >
- Midrange and Enterprise Storage
- >
- HPE EVA Storage
- >
- Re: MSA SAN Switch 2/8 Repeating console message: ...
HPE EVA Storage
1753922
Members
7529
Online
108810
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-26-2008 04:22 AM
тАО02-26-2008 04:22 AM
MSA SAN Switch 2/8 Repeating console message: "No change" "Committing configuration...Done"
Good Day:
We re beginning the setup of a previosuly unconfigured MSA 1000 with two controllers and two MSA SAN Switches 2/8 switches.
One SAN Switch 2/8 sends no unexpected console messages.
The other sends to the console display
"No change"
"Committing configuration...Done"
about every minute.
This happens with this controller in either MSA rear slot, by itself in either MSA rear slot, with one or two controllers in front of the MSA.
MSA Controllers on latest 7.x firmware
SAN switches on latest firmware 3.2.1c.
No fC connections to anything yet. Added 1 FC transmitter to each switch.
Any guidance would be most appreciated.
Thank you
virtsail
We re beginning the setup of a previosuly unconfigured MSA 1000 with two controllers and two MSA SAN Switches 2/8 switches.
One SAN Switch 2/8 sends no unexpected console messages.
The other sends to the console display
"No change"
"Committing configuration...Done"
about every minute.
This happens with this controller in either MSA rear slot, by itself in either MSA rear slot, with one or two controllers in front of the MSA.
MSA Controllers on latest 7.x firmware
SAN switches on latest firmware 3.2.1c.
No fC connections to anything yet. Added 1 FC transmitter to each switch.
Any guidance would be most appreciated.
Thank you
virtsail
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-26-2008 09:03 PM
тАО02-26-2008 09:03 PM
Re: MSA SAN Switch 2/8 Repeating console message: "No change" "Committing configuration...Done"
hi leo,
you could clear this by soft reset the san switch.
1) If the IP is already set, attach a network cable to san switch and telnet to it. User ID should be Admin and the password=password. If not, get a serial cable to connect to the switch.
2) Disable the switch:
> switchDisable
3) Reset to factory settings
> configDefault
4) reboot the san switch
> reboot
Perform the same task to the other redundant san switch.
If this answer your question, pls consider assign some points. Thanks!
Rgds
you could clear this by soft reset the san switch.
1) If the IP is already set, attach a network cable to san switch and telnet to it. User ID should be Admin and the password=password. If not, get a serial cable to connect to the switch.
2) Disable the switch:
> switchDisable
3) Reset to factory settings
> configDefault
4) reboot the san switch
> reboot
Perform the same task to the other redundant san switch.
If this answer your question, pls consider assign some points. Thanks!
Rgds
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-26-2008 03:08 AM
тАО08-26-2008 03:08 AM
Re: MSA SAN Switch 2/8 Repeating console message: "No change" "Committing configuration...Done"
I am seeing exactly the same behaviour.
This did not go away after configdefault and firmware update on the unconfigured switches.
This type of switches does not have the factory reset like newer switches. No explanation in any manual either.
Any help appreciated.
This did not go away after configdefault and firmware update on the unconfigured switches.
This type of switches does not have the factory reset like newer switches. No explanation in any manual either.
Any help appreciated.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-31-2011 05:12 AM
тАО08-31-2011 05:12 AM
Re: MSA SAN Switch 2/8 Repeating console message: "No change" "Committing configurat
Khairy, I have an msa1000 that's getting the "No Change" Commiting confuration....Done" message, do you remember or was there a fix for this.
Thanks,
Bob
Thanks,
Bob
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP