MSA1000,How to change a failed disk?

[hgping_1]

One disk in MSA1000 failed. I changed a new disk but found the data in Lun had been lost.
See the .txt
How to change a failed disk in MSA1000?
Thanks!!!!

[hgping_1]

show information

[Greybeard]

nothing obvious in these logs that show why the spare failed to kick in, but I note the firmware is very old and it may help to get 5.2 (or 5.3 but I've not used that one with VMS, it was an update to add win2008) installed, it will also give more useful info about the physical disks (model, firmware etc) in the tech_support output.

[hgping_1]

The content of .txt
*********************************
CLI> show disks
Disk List: (box,bay) (bus,ID) Size Units
Disk102 (1,02) (0,01) 36.4GB 10
Disk103 (1,03) (0,02) 36.4GB 11
Disk104 (1,04) (0,03) 36.4GB 11
Disk105 (1,05) (0,04) 36.4GB 12
Disk106 (1,06) (0,05) 36.4GB 12
Disk107 (1,07) (0,08) 36.4GB 10, 11, 12 (spare)

CLI> show unit 10

Unit 10:
In PDLA mode, Unit 10 is Lun 11; In VSA mode, Unit 10 is Lun 10.
Unit Identifier : 1
Device Identifier : 600805F3-000D2DC0-00000000-1E270004
Cache Status : Enabled
Max Boot Partition: Enabled
Volume Status : VOLUME OK
Mirror Init Status: Complete
2 Data Disk(s) used by lun 10:
Disk101: Box 1, Bay 01, (SCSI bus 0, SCSI id 0) DRIVE FAILED!
Disk102: Box 1, Bay 02, (SCSI bus 0, SCSI id 1)
Spare Disk(s) used by lun 10:
Disk107: Box 1, Bay 07, (SCSI bus 0, SCSI id 8)
Logical Volume Raid Level: MIRROR FAULT TOLERANCE (Raid 1)
stripe_size=128kB
Logical Volume Capacity : 34,726MB

CLI> show units

Unit 10:
In PDLA mode, Unit 10 is Lun 11; In VSA mode, Unit 10 is Lun 10.
Unit Identifier : 1
Device Identifier : 600805F3-000D2DC0-00000000-1E270004
Cache Status : Enabled
Max Boot Partition: Enabled
Volume Status : VOLUME OK
Mirror Init Status: Complete
2 Data Disk(s) used by lun 10:
Disk101: Box 1, Bay 01, (SCSI bus 0, SCSI id 0) DRIVE FAILED!
Disk102: Box 1, Bay 02, (SCSI bus 0, SCSI id 1)
Spare Disk(s) used by lun 10:
Disk107: Box 1, Bay 07, (SCSI bus 0, SCSI id 8)
Logical Volume Raid Level: MIRROR FAULT TOLERANCE (Raid 1)
stripe_size=128kB
Logical Volume Capacity : 34,726MB

Unit 11:
In PDLA mode, Unit 11 is Lun 12; In VSA mode, Unit 11 is Lun 11.
Unit Identifier : 2
Device Identifier : 600805F3-000D2DC0-00000000-68780005
Cache Status : Enabled
Max Boot Partition: Enabled
Volume Status : VOLUME OK
Mirror Init Status: Complete
2 Data Disk(s) used by lun 11:
Disk103: Box 1, Bay 03, (SCSI bus 0, SCSI id 2)
Disk104: Box 1, Bay 04, (SCSI bus 0, SCSI id 3)
Spare Disk(s) used by lun 11:
Disk107: Box 1, Bay 07, (SCSI bus 0, SCSI id 8)
Logical Volume Raid Level: MIRROR FAULT TOLERANCE (Raid 1)
stripe_size=128kB
Logical Volume Capacity : 34,726MB

Unit 12:
In PDLA mode, Unit 12 is Lun 13; In VSA mode, Unit 12 is Lun 12.
Unit Identifier : 3
Device Identifier : 600805F3-000D2DC0-00000000-FA490006
Cache Status : Enabled
Max Boot Partition: Enabled
Volume Status : VOLUME OK
Mirror Init Status: Complete
2 Data Disk(s) used by lun 12:
Disk105: Box 1, Bay 05, (SCSI bus 0, SCSI id 4)
Disk106: Box 1, Bay 06, (SCSI bus 0, SCSI id 5)
Spare Disk(s) used by lun 12:
Disk107: Box 1, Bay 07, (SCSI bus 0, SCSI id 8)
Logical Volume Raid Level: MIRROR FAULT TOLERANCE (Raid 1)
stripe_size=128kB
Logical Volume Capacity : 34,726MB

CLI> show disks
Disk List: (box,bay) (bus,ID) Size Units
Disk102 (1,02) (0,01) 36.4GB 10
Disk103 (1,03) (0,02) 36.4GB 11
Disk104 (1,04) (0,03) 36.4GB 11
Disk105 (1,05) (0,04) 36.4GB 12
Disk106 (1,06) (0,05) 36.4GB 12
Disk107 (1,07) (0,08) 36.4GB 10, 11, 12 (spare)

CLI> show units 11

Unit 11:
In PDLA mode, Unit 11 is Lun 12; In VSA mode, Unit 11 is Lun 11.
Unit Identifier : 2
Device Identifier : 600805F3-000D2DC0-00000000-68780005
Cache Status : Enabled
Max Boot Partition: Enabled
Volume Status : VOLUME OK
Mirror Init Status: Complete
2 Data Disk(s) used by lun 11:
Disk103: Box 1, Bay 03, (SCSI bus 0, SCSI id 2)
Disk104: Box 1, Bay 04, (SCSI bus 0, SCSI id 3)
Spare Disk(s) used by lun 11:
Disk107: Box 1, Bay 07, (SCSI bus 0, SCSI id 8)
Logical Volume Raid Level: MIRROR FAULT TOLERANCE (Raid 1)
stripe_size=128kB
Logical Volume Capacity : 34,726MB

CLI> show unit 12

Unit 12:
In PDLA mode, Unit 12 is Lun 13; In VSA mode, Unit 12 is Lun 12.
Unit Identifier : 3
Device Identifier : 600805F3-000D2DC0-00000000-FA490006
Cache Status : Enabled
Max Boot Partition: Enabled
Volume Status : VOLUME OK
Mirror Init Status: Complete
2 Data Disk(s) used by lun 12:
Disk105: Box 1, Bay 05, (SCSI bus 0, SCSI id 4)
Disk106: Box 1, Bay 06, (SCSI bus 0, SCSI id 5)
Spare Disk(s) used by lun 12:
Disk107: Box 1, Bay 07, (SCSI bus 0, SCSI id 8)
Logical Volume Raid Level: MIRROR FAULT TOLERANCE (Raid 1)
stripe_size=128kB
Logical Volume Capacity : 34,726MB

CLI> show units 11

Unit 11:
In PDLA mode, Unit 11 is Lun 12; In VSA mode, Unit 11 is Lun 11.
Unit Identifier : 2
Device Identifier : 600805F3-000D2DC0-00000000-68780005
Cache Status : Enabled
Max Boot Partition: Enabled
Volume Status : VOLUME OK
Mirror Init Status: Complete
2 Data Disk(s) used by lun 11:
Disk103: Box 1, Bay 03, (SCSI bus 0, SCSI id 2)
Disk104: Box 1, Bay 04, (SCSI bus 0, SCSI id 3)
Spare Disk(s) used by lun 11:
Disk107: Box 1, Bay 07, (SCSI bus 0, SCSI id 8)
Logical Volume Raid Level: MIRROR FAULT TOLERANCE (Raid 1)
stripe_size=128kB
Logical Volume Capacity : 34,726MB

CLI> show disks
Disk List: (box,bay) (bus,ID) Size Units
Disk102 (1,02) (0,01) 36.4GB 10
Disk103 (1,03) (0,02) 36.4GB 11
Disk104 (1,04) (0,03) 36.4GB 11
Disk105 (1,05) (0,04) 36.4GB 12
Disk106 (1,06) (0,05) 36.4GB 12
Disk107 (1,07) (0,08) 36.4GB 10, 11, 12 (spare)
***************************************insert a new disk in disk101****************************************************************

CLI> show disks
Disk List: (box,bay) (bus,ID) Size Units
Disk101 (1,01) (0,00) 36.4GB 10
Disk102 (1,02) (0,01) 36.4GB 10
Disk103 (1,03) (0,02) 36.4GB 11
Disk104 (1,04) (0,03) 36.4GB 11
Disk105 (1,05) (0,04) 36.4GB 12
Disk106 (1,06) (0,05) 36.4GB 12
Disk107 (1,07) (0,08) 36.4GB 10, 11, 12 (spare)

CLI> show unit 10

Unit 10:
In PDLA mode, Unit 10 is Lun 11; In VSA mode, Unit 10 is Lun 10.
Unit Identifier : 1
Device Identifier : 600805F3-000D2DC0-00000000-1E270004
Cache Status : Enabled
Max Boot Partition: Enabled
Volume Status : VOLUME RECOVERING (1% complete)
Mirror Init Status: Complete
2 Data Disk(s) used by lun 10:
Disk101: Box 1, Bay 01, (SCSI bus 0, SCSI id 0)
Disk102: Box 1, Bay 02, (SCSI bus 0, SCSI id 1)
Spare Disk(s) used by lun 10:
Disk107: Box 1, Bay 07, (SCSI bus 0, SCSI id 8)
Logical Volume Raid Level: MIRROR FAULT TOLERANCE (Raid 1)
stripe_size=128kB
Logical Volume Capacity : 34,726MB

CLI> show unit 10

Unit 10:
In PDLA mode, Unit 10 is Lun 11; In VSA mode, Unit 10 is Lun 10.
Unit Identifier : 1
Device Identifier : 600805F3-000D2DC0-00000000-1E270004
Cache Status : Enabled
Max Boot Partition: Enabled
Volume Status : VOLUME RECOVERING (3% complete)
Mirror Init Status: Complete
2 Data Disk(s) used by lun 10:
Disk101: Box 1, Bay 01, (SCSI bus 0, SCSI id 0)
Disk102: Box 1, Bay 02, (SCSI bus 0, SCSI id 1)
Spare Disk(s) used by lun 10:
Disk107: Box 1, Bay 07, (SCSI bus 0, SCSI id 8)
Logical Volume Raid Level: MIRROR FAULT TOLERANCE (Raid 1)
stripe_size=128kB
Logical Volume Capacity : 34,726MB

CLI> show unit 11

Unit 11:
In PDLA mode, Unit 11 is Lun 12; In VSA mode, Unit 11 is Lun 11.
Unit Identifier : 2
Device Identifier : 600805F3-000D2DC0-00000000-68780005
Cache Status : Enabled
Max Boot Partition: Enabled
Volume Status : VOLUME OK
Mirror Init Status: Complete
2 Data Disk(s) used by lun 11:
Disk103: Box 1, Bay 03, (SCSI bus 0, SCSI id 2)
Disk104: Box 1, Bay 04, (SCSI bus 0, SCSI id 3)
Spare Disk(s) used by lun 11:
Disk107: Box 1, Bay 07, (SCSI bus 0, SCSI id 8)
Logical Volume Raid Level: MIRROR FAULT TOLERANCE (Raid 1)
stripe_size=128kB
Logical Volume Capacity : 34,726MB

CLI> show unit 10

Unit 10:
In PDLA mode, Unit 10 is Lun 11; In VSA mode, Unit 10 is Lun 10.
Unit Identifier : 1
Device Identifier : 600805F3-000D2DC0-00000000-1E270004
Cache Status : Enabled
Max Boot Partition: Enabled
Volume Status : VOLUME RECOVERING (3% complete)
Mirror Init Status: Complete
2 Data Disk(s) used by lun 10:
Disk101: Box 1, Bay 01, (SCSI bus 0, SCSI id 0)
Disk102: Box 1, Bay 02, (SCSI bus 0, SCSI id 1)
Spare Disk(s) used by lun 10:
Disk107: Box 1, Bay 07, (SCSI bus 0, SCSI id 8)
Logical Volume Raid Level: MIRROR FAULT TOLERANCE (Raid 1)
stripe_size=128kB
Logical Volume Capacity : 34,726MB
*********************************************************Attention!!!!!!!!!!!!!!!!!****************************
After the recovering, the unit 10
Mirror Init Status:Waiting for first write
In operation system, the Lun10 can't be mounted.It seemed that all the data had been lost.
I had to init the Lun and backuped the data to the Lun10.

***************************************************************************************************************

CLI> show unit 11

Unit 11:
In PDLA mode, Unit 11 is Lun 12; In VSA mode, Unit 11 is Lun 11.
Unit Identifier : 2
Device Identifier : 600805F3-000D2DC0-00000000-68780005
Cache Status : Enabled
Max Boot Partition: Enabled
Volume Status : VOLUME OK
Mirror Init Status: Complete
2 Data Disk(s) used by lun 11:
Disk103: Box 1, Bay 03, (SCSI bus 0, SCSI id 2)
Disk104: Box 1, Bay 04, (SCSI bus 0, SCSI id 3)
Spare Disk(s) used by lun 11:
Disk107: Box 1, Bay 07, (SCSI bus 0, SCSI id 8)
Logical Volume Raid Level: MIRROR FAULT TOLERANCE (Raid 1)
stripe_size=128kB
Logical Volume Capacity : 34,726MB

CLI> show unit 12

Unit 12:
In PDLA mode, Unit 12 is Lun 13; In VSA mode, Unit 12 is Lun 12.
Unit Identifier : 3
Device Identifier : 600805F3-000D2DC0-00000000-FA490006
Cache Status : Enabled
Max Boot Partition: Enabled
Volume Status : VOLUME OK
Mirror Init Status: Complete
2 Data Disk(s) used by lun 12:
Disk105: Box 1, Bay 05, (SCSI bus 0, SCSI id 4)
Disk106: Box 1, Bay 06, (SCSI bus 0, SCSI id 5)
Spare Disk(s) used by lun 12:
Disk107: Box 1, Bay 07, (SCSI bus 0, SCSI id 8)
Logical Volume Raid Level: MIRROR FAULT TOLERANCE (Raid 1)
stripe_size=128kB
Logical Volume Capacity : 34,726MB


CLI> show disks
Disk List: (box,bay) (bus,ID) Size Units
Disk101 (1,01) (0,00) 36.4GB 10
Disk102 (1,02) (0,01) 36.4GB 10
Disk103 (1,03) (0,02) 36.4GB 11
Disk104 (1,04) (0,03) 36.4GB 11
Disk105 (1,05) (0,04) 36.4GB 12
Disk106 (1,06) (0,05) 36.4GB 12
Disk107 (1,07) (0,08) 36.4GB 10, 11, 12 (spare)

[hgping_1]

Show information
********************************************
LI> show tech_support

CLI> show version
Firmware version: 4.32 build 300
Hardware Revision: 7
Internal EMU Rev: 1.86 (GB204140HF)

CLI> show profile
Profile name = Default (Default)
Mode 0 = Peripheral Device LUN Addressing
Mode 1 = Legacy Failover
Mode 2 = Logical volumes connect as available on Backup Controller
Mode 3 = Product ID of 'MSA1000 VOLUME'
Mode 4 = Normal bad block handling
Mode 5 = Logout selected initiators on TPRLO
Mode 6 = Fault management events not reported through Unit Attention
Mode 7 = Do not send FCP response info with SCSI status
Mode 8 = Do not send Unit Attention on failover
Mode 9 = SCSI inquiry revision field contains the actual version
Mode 10 = SCSI inquiry vendor field contains Compaq
Mode 11 = reserved
Mode 12 = Ignore Force Unit Access on Write

Profile name = Windows
Mode 0 = Peripheral Device LUN Addressing
Mode 1 = Legacy Failover
Mode 2 = Logical volumes connect as available on Backup Controller
Mode 3 = Product ID of 'MSA1000 VOLUME'
Mode 4 = Normal bad block handling
Mode 5 = Logout selected initiators on TPRLO
Mode 6 = Fault management events not reported through Unit Attention
Mode 7 = Do not send FCP response info with SCSI status
Mode 8 = Do not send Unit Attention on failover
Mode 9 = SCSI inquiry revision field contains the actual version
Mode 10 = SCSI inquiry vendor field contains Compaq
Mode 11 = reserved
Mode 12 = Ignore Force Unit Access on Write

Profile name = Windows_SP2_and_below
Mode 0 = Peripheral Device LUN Addressing
Mode 1 = Legacy Failover
Mode 2 = Logical volumes connect as available on Backup Controller
Mode 3 = Product ID of 'MSA1000 VOLUME'
Mode 4 = Normal bad block handling
Mode 5 = Logout selected initiators on TPRLO
Mode 6 = Fault management events not reported through Unit Attention
Mode 7 = Do not send FCP response info with SCSI status
Mode 8 = Do not send Unit Attention on failover
Mode 9 = SCSI inquiry revision field contains the actual version
Mode 10 = SCSI inquiry vendor field contains Compaq
Mode 11 = reserved
Mode 12 = Enforce Force Unit Access on Write

Profile name = OpenVMS
Mode 0 = Peripheral Device LUN Addressing
Mode 1 = Asymmetric Failover
Mode 2 = Logical volumes connect as unavailable on Backup Controller
Mode 3 = Product ID of 'MSA1000 VOLUME'
Mode 4 = VMS shadow style bad block handling
Mode 5 = Logout all initiators on TPRLO
Mode 6 = Fault management events reported through Unit Attention
Mode 7 = Do not send FCP response info with SCSI status
Mode 8 = Do not send Unit Attention on failover
Mode 9 = SCSI inquiry revision field contains the actual version
Mode 10 = SCSI inquiry vendor field contains Compaq
Mode 11 = reserved
Mode 12 = Enforce Force Unit Access on Write

Profile name = Tru64
Mode 0 = Peripheral Device LUN Addressing
Mode 1 = Asymmetric Failover
Mode 2 = Logical volumes connect as unavailable on Backup Controller
Mode 3 = Product ID of 'MSA1000 VOLUME'
Mode 4 = Normal bad block handling
Mode 5 = Logout all initiators on TPRLO
Mode 6 = Fault management events reported through Unit Attention
Mode 7 = Do not send FCP response info with SCSI status
Mode 8 = Send Unit Attention on failover
Mode 9 = SCSI inquiry revision field contains the actual version
Mode 10 = SCSI inquiry vendor field contains Compaq
Mode 11 = reserved
Mode 12 = Enforce Force Unit Access on Write

Profile name = Linux
Mode 0 = Peripheral Device LUN Addressing
Mode 1 = Asymmetric Failover
Mode 2 = Logical volumes connect as available on Backup Controller
Mode 3 = Product ID of 'MSA1000 VOLUME'
Mode 4 = Normal bad block handling
Mode 5 = Logout all initiators on TPRLO
Mode 6 = Fault management events not reported through Unit Attention
Mode 7 = Send FCP response info with SCSI status
Mode 8 = Do not send Unit Attention on failover
Mode 9 = SCSI inquiry revision field contains the actual version
Mode 10 = SCSI inquiry vendor field contains Compaq
Mode 11 = reserved
Mode 12 = Enforce Force Unit Access on Write

Profile name = Solaris
Mode 0 = Peripheral Device LUN Addressing
Mode 1 = Asymmetric Failover
Mode 2 = Logical volumes connect as available on Backup Controller
Mode 3 = Product ID of 'MSA1000 VOLUME'
Mode 4 = Normal bad block handling
Mode 5 = Logout all initiators on TPRLO
Mode 6 = Fault management events not reported through Unit Attention
Mode 7 = Send FCP response info with SCSI status
Mode 8 = Do not send Unit Attention on failover
Mode 9 = SCSI inquiry revision field contains the actual version
Mode 10 = SCSI inquiry vendor field contains Compaq
Mode 11 = reserved
Mode 12 = Enforce Force Unit Access on Write

Profile name = Netware
Mode 0 = Peripheral Device LUN Addressing
Mode 1 = Asymmetric Failover
Mode 2 = Logical volumes connect as available on Backup Controller
Mode 3 = Product ID of 'MSA1000 VOLUME'
Mode 4 = Normal bad block handling
Mode 5 = Logout all initiators on TPRLO
Mode 6 = Fault management events not reported through Unit Attention
Mode 7 = Send FCP response info with SCSI status
Mode 8 = Do not send Unit Attention on failover
Mode 9 = SCSI inquiry revision field contains the actual version
Mode 10 = SCSI inquiry vendor field contains Compaq
Mode 11 = reserved
Mode 12 = Enforce Force Unit Access on Write

Profile name = HP
Mode 0 = Volume Set Addressing
Mode 1 = Asymmetric Failover
Mode 2 = Logical volumes connect as available on Backup Controller
Mode 3 = Product ID of 'MSA1000 VOLUME'
Mode 4 = Normal bad block handling
Mode 5 = Logout all initiators on TPRLO
Mode 6 = Fault management events not reported through Unit Attention
Mode 7 = Send FCP response info with SCSI status
Mode 8 = Do not send Unit Attention on failover
Mode 9 = SCSI inquiry revision field contains the actual version
Mode 10 = SCSI inquiry vendor field contains Compaq
Mode 11 = reserved
Mode 12 = Enforce Force Unit Access on Write


CLI> show globals

Global Parameters:
System Name:
Rebuild Priority: high
Expand Priority: high

Total Cache: 512MB
50% Read Cache: 256MB
50% Write Cache: 256MB

Temperature:
EMU: 24 Celsius, 75 Fahrenheit
PS1: 34 Celsius, 93 Fahrenheit
PS2: 40 Celsius, 104 Fahrenheit
FIBRE BAY: 38 Celsius, 100 Fahrenheit

CLI> show acl

ACL is disabled. To enable ACL use 'add acl'.

CLI> show connections

Connection Name: scc1-1
Host WWNN = 20000000-C93D211D
Host WWPN = 10000000-C93D211D
Profile Name = OpenVMS
Unit Offset = 0
Controller 2 Port 1 Status = Online

Connection Name: scc2-1
Host WWNN = 20000000-C93D2123
Host WWPN = 10000000-C93D2123
Profile Name = OpenVMS
Unit Offset = 0
Controller 2 Port 1 Status = Online
s

bu-1
Host WWNN = 20000000-C93D211E
Host WWPN = 10000000-C93D211E
Profile Name = OpenVMS
Unit Offset = 0
Controller 2 Port 1 Status = Online
k s
List: (box,bay) (bus,ID) Size Units
Disk101 (1,01) (0,00) 36.4GB 10
Disk102 (1,02) (0,01) 36.4GB 10
Disk103 (1,03) (0,02) 36.4GB 11
Disk104 (1,04) (0,03) 36.4GB 11
Disk105 (1,05) (0,04) 36.4GB 12
Disk106 (1,06) (0,05) 36.4GB 12
Disk107 (1,07) (0,08) 36.4GB 10, 11, 12 (spare)
Disk108 (1,08) (1,00) 36.4GB 10, 11, 12 (spare)

Unit 10:
In PDLA mode, Unit 10 is Lun 11; In VSA mode, Unit 10 is Lun 10.
Unit Identifier : 1
Device Identifier : 600805F3-000D2DC0-00000000-1E270004
Cache Status : Enabled
Max Boot Partition: Enabled
Volume Status : VOLUME OK
Mirror Init Status: Complete
2 Data Disk(s) used by lun 10:
Disk101: Box 1, Bay 01, (SCSI bus 0, SCSI id 0)
Disk102: Box 1, Bay 02, (SCSI bus 0, SCSI id 1)
Spare Disk(s) used by lun 10:
Disk107: Box 1, Bay 07, (SCSI bus 0, SCSI id 8)
Disk108: Box 1, Bay 08, (SCSI bus 1, SCSI id 0)
Logical Volume Raid Level: MIRROR FAULT TOLERANCE (Raid 1)
stripe_size=128kB
Logical Volume Capacity : 34,726MB

Unit 11:
In PDLA mode, Unit 11 is Lun 12; In VSA mode, Unit 11 is Lun 11.
Unit Identifier : 2
Device Identifier : 600805F3-000D2DC0-00000000-68780005
Cache Status : Enabled
Max Boot Partition: Enabled
Volume Status : VOLUME OK
Mirror Init Status: Complete
2 Data Disk(s) used by lun 11:
Disk103: Box 1, Bay 03, (SCSI bus 0, SCSI id 2)
Disk104: Box 1, Bay 04, (SCSI bus 0, SCSI id 3)
Spare Disk(s) used by lun 11:
Disk107: Box 1, Bay 07, (SCSI bus 0, SCSI id 8)
Disk108: Box 1, Bay 08, (SCSI bus 1, SCSI id 0)
Logical Volume Raid Level: MIRROR FAULT TOLERANCE (Raid 1)
stripe_size=128kB
Logical Volume Capacity : 34,726MB

Unit 12:
In PDLA mode, Unit 12 is Lun 13; In VSA mode, Unit 12 is Lun 12.
Unit Identifier : 3
Device Identifier : 600805F3-000D2DC0-00000000-FA490006
Cache Status : Enabled
Max Boot Partition: Enabled
Volume Status : VOLUME OK
Mirror Init Status: Complete
2 Data Disk(s) used by lun 12:
Disk105: Box 1, Bay 05, (SCSI bus 0, SCSI id 4)
Disk106: Box 1, Bay 06, (SCSI bus 0, SCSI id 5)
Spare Disk(s) used by lun 12:
Disk107: Box 1, Bay 07, (SCSI bus 0, SCSI id 8)
Disk108: Box 1, Bay 08, (SCSI bus 1, SCSI id 0)
Logical Volume Raid Level: MIRROR FAULT TOLERANCE (Raid 1)
stripe_size=128kB
Logical Volume Capacity : 34,726MB

Connection Name: scc2-2
Host WWNN = 20000000-C93D2221
Host WWPN = 10000000-C93D2221
Profile Name = OpenVMS
Unit Offset = 0
s Controller 1 Port 1 Status = Online

Connection Name: bu-2
Host WWNN = 20000000-C93B66B0
Host WWPN = 10000000-C93B66B0
Profile Name = OpenVMS
Unit Offset = 0
sController:
MSA1000(c) Compaq P56350FX3QB0DF Software 4.32 Build 300 Hardware 7
Controller Identifer: 41
NODE_ID = 500805F3-000D2DC0
SCSI_VERSION = SCSI-3
Supported Redundancy Mode: Active/Standby
Current Redundancy Mode: Active/Standby
Current Role: Active
Device Port SCSI address 7
Terminal speed for the CLI is set to 19200.
Host Port_1:
REPORTED PORT_ID 500805F3-000D2DC9
PORT_1_TOPOLOGY = F_Port
Cache:
256 megabyte read cache 256 megabyte write cache Version 2
Cache is GOOD, and Cache is enabled.
No unflushed data in cache
Battery:
Module #1 is fully charged and turned off.
Module #2 is fully charged and turned off.
Controller 1 Port 1 Status = Online

Connection Name: scc1-2
Host WWNN = 20000000-C938E57E
Host WWPN = 10000000-C938E57E
Profile Name = OpenVMS
Unit Offset = 0
Controller:
MSA1000(c) Compaq P56350FX3Q10HO Software 4.32 Build 300 Hardware 7
Controller Identifer: 40
NODE_ID = 500805F3-000D2DC0
SCSI_VERSION = SCSI-3
Supported Redundancy Mode: Active/Standby
Current Redundancy Mode: Active/Standby
Current Role: Standby
Device Port SCSI address 6
Terminal speed for the CLI is set to 19200.
Host Port_1:
REPORTED PORT_ID 500805F3-000D2DC1
PORT_1_TOPOLOGY = F_Port
Cache:
256 megabyte read cache 256 megabyte write cache Version 2
Cache is GOOD, and Cache is enabled.
No unflushed data in cache
Battery:
Module #1 is fully charged and turned off.
Module #2 is fully charged and turned off.
Controller 1 Port 1 Status = Online


CLI> show this_controller
Controller:
MSA1000(c) Compaq P56350FX3QB0DF Software 4.32 Build 300 Hardware 7
Controller Identifer: 41
NODE_ID = 500805F3-000D2DC0
SCSI_VERSION = SCSI-3
Supported Redundancy Mode: Active/Standby
Current Redundancy Mode: Active/Standby
Current Role: Active
Device Port SCSI address 7
Terminal speed for the CLI is set to 19200.
Host Port_1:
REPORTED PORT_ID 500805F3-000D2DC9
PORT_1_TOPOLOGY = F_Port
Cache:
256 megabyte read cache 256 megabyte write cache Version 2
Cache is GOOD, and Cache is enabled.
No unflushed data in cache
Battery:
Module #1 is fully charged and turned off.
Module #2 is fully charged and turned off.

CLI> show other_controller
Controller:
MSA1000(c) Compaq P56350FX3Q10HO Software 4.32 Build 300 Hardware 7
Controller Identifer: 40
NODE_ID = 500805F3-000D2DC0
SCSI_VERSION = SCSI-3
Supported Redundancy Mode: Active/Standby
Current Redundancy Mode: Active/Standby
Current Role: Standby
Device Port SCSI address 6
Terminal speed for the CLI is set to 19200.
Host Port_1:
REPORTED PORT_ID 500805F3-000D2DC1
PORT_1_TOPOLOGY = F_Port
Cache:
256 megabyte read cache 256 megabyte write cache Version 2
Cache is GOOD, and Cache is enabled.
No unflushed data in cache
Battery:
Module #1 is fully charged and turned off.
Module #2 is fully charged and turned off.

CLI>

[hgping_1]

Anybody help,thx!!!!

[hgping_1]

thank you !!!!!