HPE EVA Storage

NSR Fiber chanel Port doesnt activeted ..

 
Alborz-Mahmoodi
Frequent Advisor

NSR Fiber chanel Port doesnt activeted ..

Hi,
I configured NSR step by step as mentioned in hp NSR documentation, and i received the attach error.
please guide me how to solve this problem.

Regards,

10 REPLIES 10
Steven Clementi
Honored Contributor

Re: NSR Fiber chanel Port doesnt activeted ..

Somewhere in the interface there is a place yo change the port topology.. I don;t remember where, but see what it is set to... and post a screenshot if possible.


Steven
Steven Clementi
HP Master ASE, Storage, Servers, and Clustering
MCSE (NT 4.0, W2K, W2K3)
VCP (ESX2, Vi3, vSphere4, vSphere5, vSphere 6.x)
RHCE
NPP3 (Nutanix Platform Professional)
Uwe Zessin
Honored Contributor

Re: NSR Fiber chanel Port doesnt activeted ..

It's in the screenshot:
Port Mode ..... N_Port
.
Steven Clementi
Honored Contributor

Re: NSR Fiber chanel Port doesnt activeted ..

I remember a drop down combo box where you can "set" the topology. Just don't remember all of the settings. Thought they were AL and Fabric.

The screenshot only shows the current setting, not the available selections... ;o)
Steven Clementi
HP Master ASE, Storage, Servers, and Clustering
MCSE (NT 4.0, W2K, W2K3)
VCP (ESX2, Vi3, vSphere4, vSphere5, vSphere 6.x)
RHCE
NPP3 (Nutanix Platform Professional)
Alborz-Mahmoodi
Frequent Advisor

Re: NSR Fiber chanel Port doesnt activeted ..

Hi,

thanks about your reply ,
I attached the picture about the SCSI tracking with some protocol future and please guide me
how can i configure this?

thanks about your consideration.
Marino Meloni_1
Honored Contributor

Re: NSR Fiber chanel Port doesnt activeted ..

your FC port config looks fine if you connect to a switch port
the link status down indicate that the nsr is not logged in the switch
-check the cable
-check if the switch port is set at 4 Gb
-check the switch log and see if there are errors
-eventually set the communication speed at 2Gb on the NSR and on the Switch
-be sure the NSR FW is up to date
Alborz-Mahmoodi
Frequent Advisor

Re: NSR Fiber chanel Port doesnt activeted ..

Hi,

I connected this MSL to server without any switch.the connection is direct.

????!!!
Marino Meloni_1
Honored Contributor

Re: NSR Fiber chanel Port doesnt activeted ..

oh, then you should set the port mode as AL_PA and give a hard address to the port, the address should be different then the hard address you set on your HBA obviously
01 and 02 for example
also the speed should be the same (1GB, 2GB or 4GB)
Alborz-Mahmoodi
Frequent Advisor

Re: NSR Fiber chanel Port doesnt activeted ..

Thanks about your reply .
I'll check it and i'll tell you the conclusion.
Alborz-Mahmoodi
Frequent Advisor

Re: NSR Fiber chanel Port doesnt activeted ..

Hi,

I did your suggestion and all of thing works fine but unfortunately i have another problem on my library so the error code is:
error code : 3300 (HARD)
Rotary jammed .
As I was trying to update the library firmware with LTT software , this error appeared :
SCSI TUR failure with Sense ConditionSCSI TUR failure with Sense Condition
Sense Information: Sensekey: 0x4, ASC/ASCQ: 0x15/0x1 (MECHANICAL POSITIONING ERROR)

thanks about your consideration.