- Community Home
- >
- Storage
- >
- Midrange and Enterprise Storage
- >
- HPE EVA Storage
- >
- Problem with HP-UX 11.31 and Xiotech Emprise 7000
HPE EVA Storage
1752795
Members
5995
Online
108789
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-05-2009 04:43 AM
тАО05-05-2009 04:43 AM
Re: Problem with HP-UX 11.31 and Xiotech Emprise 7000
Hello Darryl,
yes, you might give it a try and remove the additional paths. But the mass storage stack in 11iv3 has been completely reworked and what was working with previous versions might not be working with v3 anymore. 11iv3 does have a built in device multipathing capabilities. Are you using legacy or persistent device files ?
Jozef
yes, you might give it a try and remove the additional paths. But the mass storage stack in 11iv3 has been completely reworked and what was working with previous versions might not be working with v3 anymore. 11iv3 does have a built in device multipathing capabilities. Are you using legacy or persistent device files ?
Jozef
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-05-2009 04:55 AM
тАО05-05-2009 04:55 AM
Re: Problem with HP-UX 11.31 and Xiotech Emprise 7000
The ioscan -fnC disk shows only the local disks. We did see some LUNs once and were able to connect to them and use them VxVM. The LUNs didn't show up until our SAN admin created one additional LUN as a test. When that was done the server saw the test LUN and one of the other LUNs previously unavaiable. We decided at that point that maybe recreating all the LUNs was the answer. However, that did not work. After recreating all the LUNs ther server was back to not seeing any LUNs at all.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-05-2009 05:56 AM
тАО05-05-2009 05:56 AM
Re: Problem with HP-UX 11.31 and Xiotech Emprise 7000
> After recreating all the LUNs ther server was back to not seeing any LUNs at all.
Have you rebooted the server since then? If not either reboot the server or see if you need to go through a "fcmsutil/replace_dsk" process. Take a look at page 29 of http://docs.hp.com/en/5991-5288/5991-5288.pdf
Also check the fiber card and ensure all devices are there starting on page 12 of http://docs.hp.com/en/A6795-90007/A6795-90007.pdf
Another thing to look at is if there are any firmware upgrades needed for the server and the FC cards for 11.31.
Have you rebooted the server since then? If not either reboot the server or see if you need to go through a "fcmsutil/replace_dsk" process. Take a look at page 29 of http://docs.hp.com/en/5991-5288/5991-5288.pdf
Also check the fiber card and ensure all devices are there starting on page 12 of http://docs.hp.com/en/A6795-90007/A6795-90007.pdf
Another thing to look at is if there are any firmware upgrades needed for the server and the FC cards for 11.31.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-24-2010 03:18 PM
тАО02-24-2010 03:18 PM
Re: Problem with HP-UX 11.31 and Xiotech Emprise 7000
Make sure you have a lun mapped as lun 0 on the Xiotech array. We had the same problem until I created lun 0.
- « Previous
-
- 1
- 2
- Next »
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP