- Community Home
- >
- Storage
- >
- Midrange and Enterprise Storage
- >
- HPE EVA Storage
- >
- Re: interconnection MSA 1000 and EVA 4400
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-22-2009 07:54 AM
тАО05-22-2009 07:54 AM
interconnection MSA 1000 and EVA 4400
Is it possible to interconnect (Daisy Chain) MSA and EVA switches to make the copy so that the hosts on the MSA see the EVA LUNs?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-22-2009 08:18 AM
тАО05-22-2009 08:18 AM
Re: interconnection MSA 1000 and EVA 4400
yes, after the zone merge, and the multipathing coexistence is covered in your next thread:
http://forums13.itrc.hp.com/service/forums/questionanswer.do?threadId=1342124
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-23-2009 05:46 PM
тАО05-23-2009 05:46 PM
Re: interconnection MSA 1000 and EVA 4400
Can you help with these ideas below?
1) I'd connect (daisy chain)one side of a FC cable let's say, port 1 on the MSA 2/8 switch then connect the other side to the EVA switch on let's say port 1 as well.
2) The ports on both switch should auto detect and auto configure for E_Port?
3) If I have a server connected to the MSA1000 switch, how will the server be able to get to a LUN in the EVA? or going backwards how will the EVA present one of its LUNs to the server connected to the MSA?
Or could help and explain general steps to achieve this connection?
-------------------------
Valuable help will be rewarded
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-23-2009 08:11 PM
тАО05-23-2009 08:11 PM
Re: interconnection MSA 1000 and EVA 4400
if you have 2 switches with active zones then here is the zone merger tool:
http://community.brocade.com/home/thread/2654
if the MSA 2/8 does not have the zoning enabled, e.g. this thread could help you:
http://forums13.itrc.hp.com/service/forums/questionanswer.do?admit=109447627+1243137944228+28353475&threadId=1077190
to resume it:
the main problem is that mostprobably both switches have the same Domain ID, which needs to be changed on one of them (e.g. 2/8). But you need to go offline with the switch (switchdisable) and then enter the command configure and change the domain ID in the fabric setting section...
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-23-2009 08:17 PM
тАО05-23-2009 08:17 PM
Re: interconnection MSA 1000 and EVA 4400
yes but first portdisable those ports to have all in your hands and first you need to check the Domain IDs of both switches - they need to be unique)
2)
yes unless they are not set to the fixed speed on any of the 2 switches, then the port on the second must be set on the same speed
3) you need to create new zones for the EVA hosts to see the MSA and vice versa.