- Community Home
- >
- Software
- >
- HPE OneView
- >
- HPE Blade System - Production environment - Onevie...
-
- Forums
-
- Advancing Life & Work
- Advantage EX
- Alliances
- Around the Storage Block
- HPE Ezmeral: Uncut
- OEM Solutions
- Servers & Systems: The Right Compute
- Tech Insights
- The Cloud Experience Everywhere
- HPE Blog, Austria, Germany & Switzerland
- Blog HPE, France
- HPE Blog, Italy
- HPE Blog, Japan
- HPE Blog, Middle East
- HPE Blog, Russia
- HPE Blog, Saudi Arabia
- HPE Blog, South Africa
- HPE Blog, UK & Ireland
-
Blogs
- Advancing Life & Work
- Advantage EX
- Alliances
- Around the Storage Block
- HPE Blog, Latin America
- HPE Blog, Middle East
- HPE Blog, Saudi Arabia
- HPE Blog, South Africa
- HPE Blog, UK & Ireland
- HPE Ezmeral: Uncut
- OEM Solutions
- Servers & Systems: The Right Compute
- Tech Insights
- The Cloud Experience Everywhere
-
Information
- Community
- Welcome
- Getting Started
- FAQ
- Ranking Overview
- Rules of Participation
- Tips and Tricks
- Resources
- Announcements
- Email us
- Feedback
- Information Libraries
- Integrated Systems
- Networking
- Servers
- Storage
- Other HPE Sites
- Support Center
- Aruba Airheads Community
- Enterprise.nxt
- HPE Dev Community
- Cloud28+ Community
- Marketplace
-
Forums
-
Blogs
-
Information
-
English
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
05-20-2019 02:35 AM
05-20-2019 02:35 AM
HPE Blade System - Production environment - Oneview upgrade
Dears,
I have an HPE Blade System (C7000 enclosure, 2x flexfabric 20/40 f8 virtual connect module, 8x BL460c Gen9, Oneview 3.0) along with VMware vSphere Enterprise with over than 300 Production VMs.
Now, I 'm trying to add 8x BL460c gen 10
The problem is, when I tryied to make a virtual connect profile for any Gen 10 server, the Oneview 3.0 gives me a message that the Gen10 is not supported.
For that I'm going to upgrade the Oneview 3.0 to 4.0
Here I have two qustions:
1- Do I need to buy a new License for the Oneview 4 or the installed Oneview 3 license will work with the new one.
2- Does the flex fabric connectivity will be lost during the upgrade.
Appreciating your help, and thanks in advance.
- Tags:
- OneView
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
05-21-2019 04:08 AM
05-21-2019 04:08 AM
Re: HPE Blade System - Production environment - Oneview upgrade
Hi Majd-ABs
1) No you dont have to buy any licenses if you are upgrading to 4.0 or above
2) Ideally, when you are upgrading the Oneview appliance there wont be any prod impact or any kind of network disconnectivity, You can go ahead and upgrade.
Actions
a) Before upgrade please make sure you take a backup and download / save the .bkp file from appliance.
b) Also make sure to take a VM snapshot.
c) You may need to go step wise upgrade to reach the latest version.
If you are at 3.00.05 move to 3.00.09 then > 4.00.07 > 4.00.11 > 4.10.05 > 4.20.01.01
Take a backup of the appliance after every upgrade and save it separately.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
06-09-2019 11:26 PM
06-09-2019 11:26 PM
Re: HPE Blade System - Production environment - Oneview upgrade
HI
check the firmware version of your Flex Fabric have , Gen 10 have Preliminary requirements ,
the Minimum Version that support Gen 10 is 4.50 and OnBoard admin is 4.70
check the following link
https://support.hpe.com/hpsc/doc/public/display?docId=mmr_sf-EN_US000018946
good luck !
Hewlett Packard Enterprise International
- Communities
- HPE Blogs and Forum
© Copyright 2021 Hewlett Packard Enterprise Development LP