- Community Home
- >
- Software
- >
- HPE OneView
- >
- HPE OneView for VMware vcenter version 8.0 and Sto...
-
- Forums
-
- Advancing Life & Work
- Advantage EX
- Alliances
- Around the Storage Block
- HPE Ezmeral: Uncut
- OEM Solutions
- Servers & Systems: The Right Compute
- Tech Insights
- The Cloud Experience Everywhere
- HPE Blog, Austria, Germany & Switzerland
- Blog HPE, France
- HPE Blog, Italy
- HPE Blog, Japan
- HPE Blog, Middle East
- HPE Blog, Russia
- HPE Blog, Saudi Arabia
- HPE Blog, South Africa
- HPE Blog, UK & Ireland
-
Blogs
- Advancing Life & Work
- Advantage EX
- Alliances
- Around the Storage Block
- HPE Blog, Latin America
- HPE Blog, Middle East
- HPE Blog, Saudi Arabia
- HPE Blog, South Africa
- HPE Blog, UK & Ireland
- HPE Ezmeral: Uncut
- OEM Solutions
- Servers & Systems: The Right Compute
- Tech Insights
- The Cloud Experience Everywhere
-
Information
- Community
- Welcome
- Getting Started
- FAQ
- Ranking Overview
- Rules of Participation
- Tips and Tricks
- Resources
- Announcements
- Email us
- Feedback
- Information Libraries
- Integrated Systems
- Networking
- Servers
- Storage
- Other HPE Sites
- Support Center
- Aruba Airheads Community
- Enterprise.nxt
- HPE Dev Community
- Cloud28+ Community
- Marketplace
-
Forums
-
Blogs
-
Information
-
English
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
07-25-2016 05:24 PM - last edited on 07-28-2016 12:40 PM by ChrisLynch
07-25-2016 05:24 PM - last edited on 07-28-2016 12:40 PM by ChrisLynch
HPE OneView for VMware vcenter version 8.0 and Storage Plugin with 3Par Support
I have installed and configured the HPE OneView for VMware vcenter appliance version 8.0
The issue that I am experiencing is when I am adding the 3PAR StoreServ the Model and Firmware are "blank" .
The 3PAR credential and dns anme are correct and certificate is correct.
Please advice.
Thanks
Paolo Marin
- Tags:
- 3PAR
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
07-25-2016 10:43 PM
07-25-2016 10:43 PM
Re: HPE OneView for VMware vcenter version 8.0
From the vcenetr point of view I cannot see the properties of the array, not avaiable.
see attached.
I have restarted the CIM on the 3par array with no results
Anyone experienced this issue?
Paolo Marin
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
07-26-2016 11:29 AM
07-26-2016 11:29 AM
Re: HPE OneView for VMware vcenter version 8.0
What 3PAR firmware version do you have on your storage system? You may have a newer version that the vCenter Plugin does not support yet.
I am an HPE employee
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
08-23-2016 08:35 PM
08-23-2016 08:35 PM
Re: HPE OneView for VMware vcenter version 8.0
Sorry for the late reply.
OS 3.2.2 - MU2 (patch up to P33)
Paolo Marin
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
09-06-2016 05:59 AM
09-06-2016 05:59 AM
Re: HPE OneView for VMware vcenter version 8.0
Hello,
Are you using a separate network for the 3Par management layer? Or is it the same management network as ESXi and OV4VC? I tried routing everything through a gateway to gain access to my storage and it would not work either. OV4VC had to be on the same network as my storage device. I also made sure that 2nd NIC was marked as Management.
Best regards,
Edward Haletky
Hewlett Packard Enterprise International
- Communities
- HPE Blogs and Forum
© Copyright 2021 Hewlett Packard Enterprise Development LP