HPE OneView
cancel
Showing results for 
Search instead for 
Did you mean: 

Migration from VCM to Oneview 3.1

Eugen Rodekuhr
Frequent Advisor

Migration from VCM to Oneview 3.1

We want to migrate a couple of enclosures from VCM to Oneview.

We are running into issues that a connection can't be found.

the message does not make sense because we have two VC ethenetnet modules with 6-8 connections from each server in bay 1 and 2 and two Fibre Vc modules (8GB / 20 Port) in bay 3 and 4 connected to a fibre HBA Mezzanine card.

Enclosure Serial Number:Confidential Info Erased

OA firmware 4.60

VC Ethernert firmware: 4.60

VC FC modules firmware: 2.15

 HP Oneview version: 3.10.04-0299553

 

Migration Compatibility Report for Enclosure INWCEC01T2-U1-M1-F11

Overview

 The enclosure "INWCEC01T2-U1-M1-F11", and the following resources will be migrated:

Enclosures    1

Virtual Connect interconnect modules    4

Servers          3

Ethernet networks   48

Fibre Channel networks     2

Server profiles          3

Enclosure group      LAN_Enc01

Logical interconnect groups          LIG__2

Total # of errors        0

Total # of warnings  2

Fibre Channel Fabrics

 NGS1LAN

 Warnings:

The OneView logical interconnect group "LIG__2" configuration does not match the Virtual Connect configuration. The following element(s) are inconsistent: Fibre Channel network "NGS1LAN" attribute(s) do not match: Typical Bandwidth,Maximum Bandwidth.

 

Resolution: Continuing with the Virtual Connect to OneView migration will use the existing OneView logical interconnect group configuration "LIG__2". If this OneView configuration is not acceptable, modify the specified OneView logical interconnect group "LIG__2" to be consistent with the Virtual Connect configuration. If no modifications are required, continue with the migration. If modifications were required, retest the compatibility.

 NGS2LAN

 Warnings:

The OneView logical interconnect group "LIG__2" configuration does not match the Virtual Connect configuration. The following element(s) are inconsistent: Fibre Channel network "NGS2LAN" attribute(s) do not match: Typical Bandwidth,Maximum Bandwidth.

 

Resolution: Continuing with the Virtual Connect to OneView migration will use the existing OneView logical interconnect group configuration "LIG__2". If this OneView configuration is not acceptable, modify the specified OneView logical interconnect group "LIG__2" to be consistent with the Virtual Connect configuration. If no modifications are required, continue with the migration. If modifications were required, retest the compatibility.

 

This is the error where the migrastion stopsd in oneview:

 Create            iusv1079

Server Profiles

11/8/17  4:54:06 pm

1 minute ago

Error1s          

Validate configuration.

 

Issue Port Mezzanine (Mezz) 1:1 was not found for connection 6.

Resolution Select a different port and try again.

 

 

MEZZ 1 is not used for an Ethernet connection, it is used and configured for a fibre channel connection.

EuRo
2 REPLIES
ChrisLynchHPE
Neighborhood Moderator

Re: Migration from VCM to Oneview 3.1

Can you provide the output from "show server {N}" in the OA (where {N} is the device bay number)?  I want to see what adapters are installed. Can you provide a screenshot of your VCM Server Profile?

Eugen Rodekuhr
Frequent Advisor

Re: Migration from VCM to Oneview 3.1

Hello Chris,

sorry for the delay, here we go:

 

 

Server Blade #13 Information:
        Type: Server Blade
        Manufacturer: HP
        Product Name: ProLiant BL460c Gen9
        Part Number: 727021-B21
        System Board Spare Part Number: 744409-001
        Serial Number: 
        Serial Number (Logical): VCX0000001
        UUID: 30373237-3132-5A43-3335-3230584B3853
        UUID (Logical): 91561852-1D3F-4A78-97DF-F3A68786764F
        Server Name: 
        Asset Tag:
        ROM Version: I36 02/17/2017
        Boot Mode: UEFI
        Secure Boot: Disabled

        CPU 1: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz (12 cores)
        CPU 2: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz (12 cores)
        Memory: 524288 MB

        FLB Adapter 1: HP FlexFabric 20Gb 2-port 650FLB Adapter
         Ethernet FlexNIC LOM1:1-a            00:17:A4:77:00:0C
         Ethernet FlexNIC LOM1:1-b            00:17:A4:77:00:10
         Ethernet FlexNIC LOM1:1-c            00:17:A4:77:00:14
         Ethernet FlexNIC LOM1:2-a            00:17:A4:77:00:0E
         Ethernet FlexNIC LOM1:2-b            00:17:A4:77:00:12
         Ethernet FlexNIC LOM1:2-c            00:17:A4:77:00:16

        Mezzanine 1: HP QMH2672 16Gb FC HBA for BladeSystem c-Class
           Port 1: 50:01:43:80:02:a4:00:98
           Port 2: 50:01:43:80:02:a4:00:9a

Management Processor Information:
        Type: iLO4
        Name: iusv1088-ilo
        Firmware Version: 2.55 Aug 16 2017
        IP Address: 172.23.104.80
        MAC Address: 50:65:F3:64:EC:0E
        Power Management Controller Version: 1.0.9
        iLO Federation Capable: Yes

 

Profile is attached now.

 

Thank you and talk to oyu soon.

Best Regards

Eugen

EuRo