- Community Home
- >
- Software
- >
- HPE OneView
- >
- Re: Oneview will not startup
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-28-2015 03:58 AM
04-28-2015 03:58 AM
Oneview will not startup
hi!
I have a oneview server running on 1.20
I rebootet it today because it was slow.
The server will not start again. IT only shows starting on the page.
Tryed to reboot it, nothing happend.
I aslo tryed to restore the hole vmware partition but nothing happen
what can i do.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-28-2015 04:58 AM
04-28-2015 04:58 AM
Re: Oneview will not startup
Hi,
you could switch the console (linux like) ALT +Fx (1-3) and see what is logged during boot.
Is network connected ? DNS available ? .....
I work for HP
Regards
Stephan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-28-2015 05:01 AM
04-28-2015 05:01 AM
Re: Oneview will not startup
Hi! You could check your disk space on VMFS/LUN/VM Disks.
Did you used Thin or Thick provisioned disks?
Grtz Peter
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-28-2015 09:53 AM
04-28-2015 09:53 AM
Re: Oneview will not startup
Hello eander, and welcome to the HP OneView community.
Typically when you see "Starting" with no progress bar movement on the VM console, it is typically disk related. What server and disk configuration are you using? If it is a local disk with a RAID controller, do you have any Write-Back Cache module installed? Have you verified that the disk where the VM is located isn't being starved of resources (long disk queue lengths, IO latency, etc.)?
Also, restoring the VMFS partition wouldn't have been a troublshooting step I would have taken.
When dealing with slow appliance performance, you should check the following host resources in order for allocation issues:
- Disk
- CPU
- RAM
There is a LOT of disk IO that occurs when an appliance is in its startup sequence. CPU can be starved if this is a reboot of an already provisioned appliance that manages resources, as it has to validate and refresh the managed and monitored hardware. RAM only if you are reaching the supported device monitored and/or managed resource limits.
I am an HPE employee
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-28-2015 08:38 AM
09-28-2015 08:38 AM
Re: Oneview will not startup
Same problem with the same version.
Anyone have any ideas? the F(x) 1,2,3 did now work for me so I can't get to the console to see whats freaked out. I did "backups" but it it kept the local to the appliance that just freaked out. Now I wonder how to backup to a external location, "if" I can get it working again. I assuem the backup files are someplace on the appliance.
The only thing I can think to do is
1. Start up a new VM from teh same or current VHD.
2. Restore teh backup from where ever I can try to get it.
Well, over a hundred servers, 40 Racks, 7 data centers, and I don't want to start from scratch.......
Note: Notificaiton appear to work, alert for a failed drive over the weekend, just no GUI to work with, only the "Starting........" screen.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-28-2015 10:43 AM
09-28-2015 10:43 AM
Re: Oneview will not startup
Hi Ray,
you could check this Advisory
http://h20564.www2.hpe.com/hpsc/doc/public/display?docId=emr_na-c04708819&sp4ts.oid=5390822
but I would recommend to open an support case.
KR
Stephan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-05-2015 04:32 AM
10-05-2015 04:32 AM
Re: Oneview will not startup
The restarting of a OneView appliance can take quite a while. In our enviroment the reboot time is 35 min.
How long did you wait for the appliance to start because sometimes it seems like nothing is happening?