- Community Home
- >
- Software
- >
- HPE OneView
- >
- Proper order for deleting LIG uplink port
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-25-2018 08:08 AM
01-25-2018 08:08 AM
Proper order for deleting LIG uplink port
Pretty sure I already know the answer to this but need some confirmation. I have a LIG that contains 3 LI's. Port 8 on each of my VC's was connected to an iscsi network that we are no longer using. I need to delete these uplink ports. My assumption is that I delete the uplink port from the LIG Which will give me an inconsistency warning on the LI's. Doing an update from group will clear that up. Its that simple right?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-25-2018 12:56 PM
01-25-2018 12:56 PM
Re: Proper order for deleting LIG uplink port
I am an HPE employee
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-25-2018 01:14 PM
01-25-2018 01:14 PM
Re: Proper order for deleting LIG uplink port
3.10.04
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-29-2018 12:30 PM
01-29-2018 12:30 PM
Re: Proper order for deleting LIG uplink port
Instead of deleting those uplinks, is there a way to disable them so they'll stop reporting as critical? Just in case we eve decide to use them again.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-29-2018 12:43 PM
01-29-2018 12:43 PM
Re: Proper order for deleting LIG uplink port
The Logical Interconnect Group (LIG) is the expected policy to be deployed. The associated Logical Interconnect (LI) is the actual configuration. And if ports associated with an Uplink Set that has been deployed to a Logical Interconnect are in a Failed state (because they are disconnected), this is by design. Adding and removing the ports from the LI by the way of the LIG can be done online. When you are ready to use those ports, just add them to your LIG configuration, and then perform an "Update from group" operation at the LI.
I am an HPE employee