- Community Home
- >
- Storage
- >
- Storage Networking
- >
- HPE Storage Networking - Switches
- >
- About SDDQ of SN6000B: SN6000BのSDDQについて
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-25-2021 09:05 PM - last edited on 01-26-2021 08:22 PM by Parvez_Admin
01-25-2021 09:05 PM - last edited on 01-26-2021 08:22 PM by Parvez_Admin
About SDDQ of SN6000B: SN6000BのSDDQについて
SNスイッチにて以下をSlow Drain Device 検知時に該当ポートを切り離す機能を実装したく思っています。
スイッチのMAPSマニュアルを参照しておりますが、以下確認させてください。
・ポート無効化のみであれば、SDDQをMAPSアクションに追加するだけでいいでしょうか?
別でMAPSルールを追加する必要ございますでしょか?
・機能利用にはQoSが必要とありますが、QoSはライセンス不要でしょうか?
また、QoSゾーニングは必要でしょうか?
Google Translated
I would like to implement a function to disconnect the corresponding port when Slow Drain Device is detected by using the SN switch.
Please refer to the MAPS manual of the switch, but check the following.
-If only port invalidation, should I just add SDDQ to the MAPS action?
Is it necessary to add a separate MAPS rule?
-QoS is required to use the function. Is QoS license-free?
Also, is QoS zoning necessary?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-26-2021 01:30 AM
02-26-2021 01:30 AM
Re: About SDDQ of SN6000B: SN6000BのSDDQについて
Hi ntaka,
-If only port invalidation, should I just add SDDQ to the MAPS action?
Is it necessary to add a separate MAPS rule? >>> Correct. Use the 'mapsconfig --actions and include SDDQ as one of the actions.
-QoS is required to use the function. Is QoS license-free?
Also, is QoS zoning necessary? >> Yes, the Quality of Service (QoS) must be enabled to use the SDDQ feature. And QoS can be configured without the license in FOS 7.2.0 and above. QoS zoning is not mandatory.
Regards,
Veeyarvi
I am an HPE Employee.
[Any personal opinions expressed are mine, and not official statements on behalf of Hewlett Packard Enterprise]