- Community Home
- >
- Networking
- >
- IMC
- >
- Re: 3NS and 1100 switch management problem
IMC
1753287
Members
5298
Online
108792
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-15-2009 07:51 AM
тАО05-15-2009 07:51 AM
3NS and 1100 switch management problem
When managing my network with 3NS I'm receiving a warning from 1100 switch: failed to register for SNMP traps. As I know it's because of too many registered ip addresses in the table. But how to clear this table on 1100 switch? I can't find appropriate options in the menu.
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-05-2009 02:54 AM
тАО06-05-2009 02:54 AM
Re: 3NS and 1100 switch management problem
Log on to the switch via the console or telnet.
select snmp , trap .
You can then use display to see the trap destinations.
then select remove.
Job done.
select snmp , trap .
You can then use display to see the trap destinations.
then select remove.
Job done.
The Doc
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-05-2009 04:18 AM
тАО06-05-2009 04:18 AM
Re: 3NS and 1100 switch management problem
Not so simple. There is no "snmp" option in the root menu of the 1100 switch, but entering this manually gives the submenu with the following options: "get", "next", "set". There is no "trap" option and it can't be entered (doing this gives an error message: "trap is not a valid selection").
What you wrote is true for a 3300 switch, but 1100 is an older device and its menu is different.
What you wrote is true for a 3300 switch, but 1100 is an older device and its menu is different.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP