HPE Community read-only access December 15, 2018
This is a maintenance upgrade. You will be able to read articles and posts, but not post or reply.
Hours:
Dec 15, 4:00 am to 10:00 am UTC
Dec 14, 10:00 pm CST to Dec 15, 4:00 am CST
Dec 14, 8:00 pm PST to Dec 15, 2:00 am PST
IMC
cancel
Showing results for 
Search instead for 
Did you mean: 

Backup Error.

 

Backup Error.

1 Initialize task parameters. Succeeded. 2016-04-01 11:19:39 2016-04-01 11:19:40


2 Back up device startup configuratio... SNMP Set operation failed.

1. Check that the SNMP parameters are correct. With SNMPv3 adopted, the username, authentication password, privacy password and privacy mode for the device and the iMC should be the same.
2. Check the MIB style (Execute the display mib-style command. If the MIB style is displayed as new, but it displays that the node sending the Set request is 2011 after packet capturing, synchronize the device. Check the MIB style again. If the MIB style is still inconsistent, execute the mib-style [ new | compatible ] command, and then restart the device.).


3. Error code such as no such name may occur for the Set operation. You need to capture packets to analyze whether such error occurs in the response received by the device.


4. Device busy, please retry later. 2016-04-01 11:19:41 2016-04-01 11:21:23
3 Initialize redo task parameters. Succeeded. 2016-04-01 11:21:23 2016-04-01 11:21:24
4 Back up device startup configuratio... Succeeded. 2016-04-01 11:21:25 2016-04-01 11:22:09

 

display mib-style
            ^
% Unrecognized command found at '^' position.

!!

4 REPLIES
LindsayHill
Honored Contributor

Re: Backup Error.

Some more information would be helpful. What sort of device are you trying to backup? Where did those last few lines come from ("display mib-style...") - was that from you typing at the CLI?

Do you want to backup this device using SNMP read/write? Or through CLI/SCP? If you don't want to use snmp read/write (or the device is not configured for it), then un-set the SNMP read/write string on the Device Details page.

Re: Backup Error.

What sort of device are you trying to backup? : HP 7506

("display mib-style...") - was that from you typing at the CLI? : YES

Do you want to backup this device using SNMP read/write? Or through CLI/SCP? :SNMP

We are getting the error during iMC device backup execution. But backup taken successfully. We have another same model device and not getting any error during device backup !

Thank You

 

Re: Backup Error.

This makes me think of a similar issue which was resolved for the HP 5130 switch.

I suggest to open a support case with Hewlett Packard Enterprise to verify and get it fixed for your device type, as well.

""
HPE 5130 EI-CMW710-R3112 Release Notes

201512090334
• Symptom: The operation of backing up the configuration file fails.
• Condition: This symptom occurs if the following conditions exist:
􀁻 The MIB node hh3cCfgOperateServerAddress is configured to specify the file backup server.
􀁻 The IP address of the file backup server is in the range of x.x.x.224 to x.x.x.255.

""

LindsayHill
Honored Contributor

Re: Backup Error.


Ramshankar Acharjee wrote:

We have another same model device and not getting any error during device backup ! 


Is the other device running the same firmware? Is it actually using SNMP read/write? Or does SNMP read/write fail, and it switches over to CLI/SCP?