- Community Home
- >
- Networking
- >
- IMC
- >
- How to remove Link-aggregation as shown as default...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-15-2020 03:49 AM
01-15-2020 03:49 AM
How to remove Link-aggregation as shown as default in Topology map? 7.3 E705P02
It's not very good when one router has a port channel to 2 devices. Then only one is showed. See below:
Link-aggregation was not seen in 7.3 E605P02
The actual po-links manually printed in red is not visible in this case.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-15-2020 11:01 AM
01-15-2020 11:01 AM
Re: How to remove Link-aggregation as shown as default in Topology map? 7.3 E705P02
Well...link aggregations (call it - HP ProCurve jargon - Port Trunking or - HPE Comware jargon - Link Aggregation Group or...Cisco EtherChannel) require that links are co-terminus...so only if you're dealing with Virtual Switches you can begin/end member links on both Virtual Switch members...otherwise...if you're usually dealing with standalone switches (and not MC-LAGs are involved) then link aggregation interface's member links need to begin and end between A peer pair (and not between/crossing pairs, one pair north and one south)...watching your attachement it looks like you're dealing with a pair of routers and each one has a link aggregation interface where two member links (one drawn red) terminate against two different standalone switches...isn't it?
I'm not an HPE Employee
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-16-2020 12:47 AM
01-16-2020 12:47 AM
Re: How to remove Link-aggregation as shown as default in Topology map? 7.3 E705P02
Exactly like this:
"watching your attachement it looks like you're dealing with a pair of routers and each one has a link aggregation interface where two member links (one drawn red) terminate against two different standalone switches...isn't it?"
So Can I solve this in any way?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-16-2020 04:36 PM
01-16-2020 04:36 PM
Re: How to remove Link-aggregation as shown as default in Topology map? 7.3 E705P02
Probably I misunderstood your issue (or the fact you believe to deal with an issue): having a device with a link aggregation defined where its member links don't co-terminate on the same physical (or virtual) switch will produce an error (the aggregation will not properly terminate on its peers interfaces)...so IMC is showing you the right thing...just one link of two (per each egressing wrong port aggregation).
I'm not an HPE Employee
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-17-2020 07:21 AM
01-17-2020 07:21 AM
Re: How to remove Link-aggregation as shown as default in Topology map? 7.3 E705P02
Hello,
If you're referring to detecting links that use Cisco's Multi-chassis Etherchannel, I am not sure if iMC has ever been able to detect these properly, but I doubt it. Was it working on previous iMC releases? If not, you'd need to contact your HPE Sales/Acct. Manager to open an Enhancement Request, in order for iMC to detect these types of links properly in a future release.
Justin
Working @ HPE
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-20-2020 01:35 AM
01-20-2020 01:35 AM
Re: How to remove Link-aggregation as shown as default in Topology map? 7.3 E705P02
In previous releases i do not see link-aggregation as I remember. I remember that I saw all links as connected.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-20-2020 01:47 AM
01-20-2020 01:47 AM
Re: How to remove Link-aggregation as shown as default in Topology map? 7.3 E705P02
Here you see 7.3 E605P06 vs 73 E705P06