- Community Home
- >
- Networking
- >
- IMC
- >
- Re: IMc v7 issues - alarm sounds and WSM - no WSM ...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-18-2014 10:46 AM
02-18-2014 10:46 AM
IMc v7 issues - alarm sounds and WSM - no WSM data
Hello,
I am having two issues that I need assitance with please. here are my versions first.
iMC PLAT 7.0 (E0102P05)
MSM 710 controller - Software version: 5.7.3.0-13117
1) How do you disable sounds for alarms? i clicked on the gear button on the bottom right and unchecked all sounds and then clicked SET but I still hear sounds.
2) WSM - I added my IMC box ip address to the Mobility Manager setting on the MSM and it says "connected to :x:xx: on p ort 7668" but in IMC, on the device properties page, I don't have the tab called "Wireless Services Information" next to Configuration Management. Therefore, I can't collect any wireless data. Any idea on how to resolve this?
NOTE: The MSM controller is classified correctly in the Wireless category. and detects it as a MSM controller.
Thank you,
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-18-2014 04:40 PM
02-18-2014 04:40 PM
Re: IMc v7 issues - alarm sounds and WSM - no WSM data
After setting the sound options, did you reload the page? See if that helps. Also, if you uncheck sounds, Set & Reload, does it then show the sounds as checked or unchecked?
For the WSM issue, have you installed the WSM module? Do you have a menu option Service -> WLAN Manager?
(Sorry if that sounds like a silly question, but I don't know your environment, and it's best to check the basics are in place before we get too deep into it).
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-18-2014 07:20 PM
02-18-2014 07:20 PM
Re: IMc v7 issues - alarm sounds and WSM - no WSM data
I set the sounds as uncheckd. I can reload the page as well. Makes no difference. Even with the sounds unchecked, they still go off.
The WSM module is installed and licensed. It shows up under Service. There's just no data in it. The only thing I did to get the WSM sending data is set the IMC address in the Mobiity Manager.
thanks,
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-18-2014 07:34 PM
02-18-2014 07:34 PM
Re: IMc v7 issues - alarm sounds and WSM - no WSM data
Wireshark also confirms that there is a steady stream of data going back and forth between IMC and the MSM controller. They are on the same subnet too.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-18-2014 07:41 PM
02-18-2014 07:41 PM
Re: IMc v7 issues - alarm sounds and WSM - no WSM data
What do you mean by "there's just no data in it" ? Is it showing 0 ACs, 0 Fit APs, etc?
Remove the MSM from IMC.
Re-add it, using the SNMP community. Give it read-write access too. (This lets you do backups).
Make sure that IMC correctly identifies the device as an MSM.
There are also some SOAP settings you can add for performance statistics. I can't directly link to the document, but search the HP Support Center for mmr_kc-0110717.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-18-2014 07:45 PM
02-18-2014 07:45 PM
Re: IMc v7 issues - alarm sounds and WSM - no WSM data
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-19-2014 02:50 PM
02-19-2014 02:50 PM
Re: IMc v7 issues - alarm sounds and WSM - no WSM data
Regarding the Alarm Sound Settings, this should be fixed in an upcoming release of IMC 7.0. Currently, after making changes to the Alarm Sound Settings, restart the jserver.exe process in the DMA >> Process Tab. Once you log back into IMC, the Alarm Sound Settings should take effect.