- Community Home
- >
- Networking
- >
- IMC
- >
- Re: Monitoring SNMP QoS HPE Comware 5510 (MIB)
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-30-2017 03:37 PM
тАО11-30-2017 03:37 PM
Monitoring SNMP QoS HPE Comware 5510 (MIB)
Hi,
I'd like to monitor by snmp the Qos configured on switch HPE 5510.
I have three class of service with different dscp and I'd like know the bandwitdh of each dscp.
Example:
I have configured the policy shown below:
traffic classifier VOIP operator and
if-match acl 3000
traffic behavior VOIP
remark dscp af31
qos policy VOIP
classifier VOIP behavior VOIP
interface GigabitEthernet1/0/24
port link-mode bridge
port access vlan 2
qos apply policy VOIP inbound
qos apply policy VOIP outbound
acl number 3000
rule 0 permit ip source 10.44.0.0 0.0.255.255 destination 10.44.0.0 0.0.255.255
I'd like to monitor the traffic IN&OUT about dscp=af31
I thought to use a "snmpwalk" for query a specific OID (MIB) about the device.
Can I do it?
Thanks
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-04-2017 01:21 AM
тАО12-04-2017 01:21 AM
Re: Monitoring SNMP QoS HPE Comware 5510 (MIB)
Hi, you have two options do see the traffic for specific DSCP.
You can do it if you install the NTA module additional to imc or the QoS module.
The default performance Management in imc PLAT does not do it for DSCP.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-06-2017 08:58 AM
тАО12-06-2017 08:58 AM
Re: Monitoring SNMP QoS HPE Comware 5510 (MIB)
Hi,
first of all thanks for your response.
I have the NTA module and I tried to collect traffic about dscp.
In fact, as you say, Imc is collecting the traffic for dscp and dot1p but I'd like obtain a specific graphic (rate in bps) to analize the trend (hour,day,week......as for throughput of interface tx/rx)......is it possible?
I haven't the QoS Module and however I'm not sure that the Qos Module may obtain the graphic for trend (rate in bps ...... hour,day,week....) for each dscp that pass through the interface. Did you try it?
Anothet things, I have seen on the PLAT Imc Default that in the Performance Management there is the Policy "Qos Matching"; before it didn't start because oh a lack of a MIB "hh3c-ifqos2.mib", i loaded it and there isn't error when activate it but it doesn't collect anything.
Thanks