- Community Home
- >
- Networking
- >
- IMC
- >
- Re: No root pass, no eth0 up in IMC 7.0, i can,t ...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-19-2016 05:56 AM
тАО01-19-2016 05:56 AM
No root pass, no eth0 up in IMC 7.0, i can,t start virtual image.
Hi, I downloaded "HP_IMC_Smart_Connect_w_WLM_VAE_7.0_E0103" and Xenserver amount from 6.5, everything went well, but does not start the network card eth0 shows me the welcome screen, but not the root password, try IMC_123, IMC123, enterIMC123 but not tube success.
The welcome screen says RHE LSR 6.1 (Santiago) and the history of services started telling me that the board is not the eth0 MAC ADRESS expected and fails.
I do not know what else to do. Please help.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-19-2016 02:11 PM
тАО01-19-2016 02:11 PM
Re: No root pass, no eth0 up in IMC 7.0, i can,t start virtual image.
I believe the password is "iMC_123" - note the lower-case i
If that doesn't work, just boot into single-user mode & reset the password.
Once you've got logged in you can sort out the MAC address problem that is causing that error message. See the documentation for how to do this.
7.0 is pretty old now though. HPE has published updated documentation for SmartConnect 7.2, but they don't seem to have published an updated appliance. I think you're better off doing a full install of IMC 7.2, rather than using the appliance.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-20-2016 03:35 AM
тАО01-20-2016 03:35 AM
Re: No root pass, no eth0 up in IMC 7.0, i can,t start virtual image.
Hello LindsayHill, thank you for responding.
I can not boot into single-user mode because it is a mv.
I'll try with lowercase i.
I'll try to version 7.2. if I can with the version 7.0
Thank you thank you very much for responding.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-20-2016 04:47 AM
тАО01-20-2016 04:47 AM
Re: No root pass, no eth0 up in IMC 7.0, i can,t start virtual image.
I again, the password does not work "iMC_123" will be another pass ??
There is no virtual machines to version 7.2 and updates would be impossible to install without root pass.
Help please!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-20-2016 09:30 AM
тАО01-20-2016 09:30 AM
Re: No root pass, no eth0 up in IMC 7.0, i can,t start virtual image.
Why can't you boot into single user mode because it is a VM? It's even easier to boot a VM into singl user-mode than a physical server.
As they have not yet published a 7.2 virtual appliance, I strongly recommend installing your own Windows or Linux VM, and installing IMC 7.2 on that.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-20-2016 09:52 AM
тАО01-20-2016 09:52 AM
Re: No root pass, no eth0 up in IMC 7.0, i can,t start virtual image.
Ok I will try, thank you very much again for the help!