IP Telephony - NBX
1748250 Members
3466 Online
108760 Solutions
New Discussion

Re: Error message when booting with Console

 
HopeHealth
Occasional Visitor

Error message when booting with Console

Sending Download Me to FF:FF:FF:FF:FF:FF

 

 

Madrid Diagnostics X1.0.0
Creation Date: Oct  9 2002
Bank 0 is enabled as:
   32 bits wide
   4 Mbits deep
   Size: 16777216 bytes
Bank 1 is disabled
Bank 2 is disabled
Bank 3 is disabled

Total DRAM memory detected: 16777216 bytes

Initializing Interrupts
Initializing memory allocation subsystem
Initializing Timers

ERROR: RTC and CMOS RAM are invalid
Time: 00:00:00
Date: Wednesday, January 1, '97
Initializing Ethernet Controller
Crystal CS8900 Ethernet Controller
Starting Memory Cell Test ... PASSED

HPI Memory Test for DSP 0:  PASSED
HPI Memory Test for DSP 1:  PASSED
HPI Memory Test for DSP 2:  PASSED
HPI Memory Test for DSP 3:  FAILED
HPI Memory Test for DSP 4:  PASSED
HPI Memory Test for DSP 5:  PASSED
HPI Memory Test for DSP 6:  PASSED
HPI Memory Test for DSP 7:  FAILED
0000008015: HPI DSP Init Msg, DSP0 OK
0000008015: HPI DSP Init Msg, DSP1 OK
0000008015: HPI DSP Init Msg, DSP2 OK
0000008015: HPI DSP Init Msg, DSP4 OK
0000008015: HPI DSP Init Msg, DSP5 OK
0000008015: HPI DSP Init Msg, DSP6 OK
.....
ROM0MapSpaceAddrStart = 0011e000
ROM0MapSpaceAddrStop = 0019d000
ROM0MapSpaceAddrOffset = fff62000
Starting copy from 0011e000 to 0019ea48
Started Boot Command Loop.

 

 

 

 

 


                            VxWorks System Boot


Copyright 1984-1998  Wind River Systems, Inc.

 

 

CPU: PC 486
Version: 5.4.2
BSP version: 1.2/0
Creation date: Oct  9 2002, 19:07:46

 


Press any key to stop auto-boot...
 1
auto-booting...

Starting Bootload, bootString = cs(0,0)T1Board:vxworks e=192.168.1.192 u=target pw=target tn=vxworks_T1Board f= 0x1000.


boot device          : cs
unit number          : 0
processor number     : 0
host name            : T1Board
file name            : vxworks
inet on ethernet (e) : 192.168.1.192
user (u)             : target
ftp password (pw)    : target
flags (f)            : 0x1000
target name (tn)     : vxworks_T1Board

Starting Ethernet Controller, pCookie = 0xffa0e0, unitNum = 0, bootDev = cs

Attached TCP/IP interface to cs0.

Current Bootloader Version:
Boot Release Type = 3, Boot Major Revision = 0
Boot Minor Revision = 0, Boot Point Revision = 7


Sending Download Me to FF:FF:FF:FF:FF:FF
Sending Download Me to FF:FF:FF:FF:FF:FF

3 REPLIES 3
bosoxfan
Trusted Contributor

Re: Error message when booting with Console

That is not really an error message

The PRI card is sending out a broadcast "download" me message looking for an NBX to talk to.. it

will continue to do this until it finds one..

 

Check connection between the card and the NBX .. are they on the same subnet???

 

 

HopeHealth
Occasional Visitor

Re: Error message when booting with Console

Im sure they are. I was hooking up my console port to see the system come up so I can go into the web gui and purge the database.

 

Do I plug the console cable into the call processor or the DLC?

 

I have attached a picture of how the front of my unit and how it is connected

HopeHealth
Occasional Visitor

Re: Error message when booting with Console

I found the issue. I was connected in correctly but I still think I have a bad Call Processor.