IP Telephony - NBX
cancel
Showing results for 
Search instead for 
Did you mean: 

How to remotely reset/reconfigure an ATA

alexb_1
Advisor

How to remotely reset/reconfigure an ATA

Any one has the command syntax for the 3Com ATA? I have a unit overseas that needs to be reconfigured. Any help would be appreciated.



Alex

11 REPLIES
bosoxfan_1
Super Advisor

Re: How to remotely reset/reconfigure an ATA

Hi

YOu can either change the settings via Netset

or if you can attach a console cable and at

the ATC prompt, type Help



nbxShowConfig - shows the current configuration

nbxSetIpAddress

nbxSetGatewayAddress

nbxSetSubnetMask

are commands for setting the config on the ATA

nbxSetNCPIpAddress - command for setting the NBX that the ATA will talk to.

maknbx_1
Frequent Advisor

Re: How to remotely reset/reconfigure an ATA

This command are possible to not show?

With SERIAL is possibile to enter another commands when in MONIOTR (PSBL) but the commands not store and the command about NCP IP is not present.

Another prolem? When you try to type help on -> the command that you desribe is not present.
bosoxfan_1
Super Advisor

Re: How to remotely reset/reconfigure an ATA

Which ATA box do you have ? what is the model?



at the -> prompt, type lkup "nbx"



this will show the nbx commands (help does not show this)

maknbx_1
Frequent Advisor

Re: How to remotely reset/reconfigure an ATA

THANKS, infact the other commands show.And now is operative.

But now for another ATA, the problem is block in a (PSBL) promt at startup.

My techical say me that put the incorrect command to load a file button, i don't know why, i suppose to select boot n to try to insert the ip addresses.

I try to boot to f and search this file (dsp_22) into directory with ls commands but ATA not boot.

Cannot find the boot file.

How to restore the ATA or put the correct path or file to boot?



THANKS a LOT
bosoxfan_1
Super Advisor

Re: How to remotely reset/reconfigure an ATA

what do you get when you boot the ATA?

sounds like the flash might be blown????

can you capture the console output and put it in this discussion?

maknbx_1
Frequent Advisor

Re: How to remotely reset/reconfigure an ATA

thanks for reply



Tomorrow i put the trace in this discussion.



For example the message is do not try the file in /bin

or when i put dsp_22 show message like the file is not supported.
maknbx_1
Frequent Advisor

Re: How to remotely reset/reconfigure an ATA

This is the trace and some commands about the problem with ATA boot.

Trace show when the problem occur when boot UP and show some information:



reboot



Minimal POST completed... Success.

Last reset cause: Software reset (memory controller also reset)



PSPBoot1.2 rev: 1.2.0.3

(c) Copyright 2002-2004 Texas Instruments, Inc. All Rights Reserved.

3COM Revision: 1.1 (for Skylark)



Press ESC for monitor... 3 3 2 1



(memsize = 0x1000000 = 16777216, _MemSize = 0x1000000 = 16777216)





***** It's ok to load the code through VisionClick *****



(psbl)

The checksums matched for OPER image

The checksums matched for Golden image

The checksums matched for Bootloader image



Boot image "/bin/-" not found.

OS boot failed.

(psbl) net help



reboot version info fa

mi mu fi duplex

printenv setenv unsetenv defragenv

fmt boot dm DM

oclk help ls df

cp cat rm tftp

config_phone set_ip set_tftp_ser_ip set_subnet_mask

set_mac set_boot set_gateway_ip ip

ti sm mac bp

gw net

(psbl) net



net ]]]]

Use a single dash for each omitted argument



net - - - - - -



(psbl) sete printenv





MEMSZ 0x01000000

FLASHSZ 0x00400000

MODETTY0 9600,n,8,1,hw

PATH /bin:/etc

CPUFREQ 162500000

MIPSFREQ 162500000

SYSFREQ 125000000

PROMPT (psbl)

IPA -

IPA_SVR -

SUBNET_MASK -

IPA_GATEWAY -

HWA_0 -

BOOTCFG m:f:"-"



(psbl)





THANSK
bosoxfan_1
Super Advisor

Re: How to remotely reset/reconfigure an ATA

hi.. looks to me like the flash is blown..



you know when you download a phone and you get on the lcd screen "downloading phone, do not unplug" while the flash is updating???



If you did, the flash is blown and the phone would have to be returned... looks like this is gone.. the flash image is blown.



sorry

maknbx_1
Frequent Advisor

Re: How to remotely reset/reconfigure an ATA

Exactly, i suppose like that and return to 3Com, when is possibile.



THANSK
nskroger
Occasional Visitor

Re: How to remotely reset/reconfigure an ATA

I am having issues using the nbxSet...commands.

 

I need to set a static IP address, subnet mask, default gateway, & set the NCP address.  When I issue the following command, I get the following.

 

-> nbxSetIpAddress 10.180.181.127
invalid number: 10.180.

 

What am I doing wrong?

bosoxfan
Trusted Contributor

Re: How to remotely reset/reconfigure an ATA

try putting the IP address in quotes

nbxSetIpAddress "10.1.1.1"