- Community Home
- >
- Networking
- >
- Legacy
- >
- IP Telephony - NBX
- >
- feature 441 - Direct to VM transfer not working
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-28-2011 11:50 AM
тАО09-28-2011 11:50 AM
feature 441 - Direct to VM transfer not working
NBX V3000 - R5_0_31 - Ethernet Only - 3103 phones
Calls from TLIMS (701-704) are answered by extension 100 via a hunt group.
Ext 100 presses programed button Direct Mail Transfer (or Feature 441, either way) and enters any extension,
The call goes into limbo and rings back to ext 100 in about 3minutes10sec.
Additionally if they do a straight transfer to another extension VM never picks up and the call times out to the org. ext.
HOWEVER INTERNALLY the feature works. x100 calls x108. x108 direct mail transfers to x109 and it works(!)
ok - so they can call ext 500 internally - but when set Auto-Ext for any TLIM to an auto attendant 500 and call the line AA500 never picks up.
be an intermittant problem in the past. Yesterday they changed telco services. Same company (TDS) different delivery. guessing a cisco product doing some T1 to analog line delivery. Now it never works.
TLIM to VM not working? or telco issue, could line voltage cause this?
thanks for any insight,
Nick Utrie
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-28-2011 12:47 PM
тАО09-28-2011 12:47 PM
Re: feature 441 - Direct to VM transfer not working
Just a wild shot.. check the vm ports.. are they all in use when the incident occurs??
Maybe tlim calls get transferred, all vm ports in use, so they wait until one is freed up, then the Transfer timeout kicks in and the call goes back to x100.
I know this does not explain why they work internally... maybe your internal testing was just lucky and a vm port had released.
Maybe tlim call is not disconnecting right away as they should be...
just a hunch.....
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-28-2011 12:59 PM - edited тАО09-28-2011 01:00 PM
тАО09-28-2011 12:59 PM - edited тАО09-28-2011 01:00 PM
Re: feature 441 - Direct to VM transfer not working
no - VM port all available during tests.
I am starting to think LOW VOLTAGE on the lines or an issue with communication between TLIMS and VM.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-28-2011 01:00 PM
тАО09-28-2011 01:00 PM
Re: feature 441 - Direct to VM transfer not working
Know of any logging that would show where the hicupp is coming from ?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-29-2011 08:32 AM
тАО09-29-2011 08:32 AM
Re: feature 441 - Direct to VM transfer not working
now Today, everything is working in re: to Direct Mail Transfer. AA answers when confiurged in TLIM auto extension. Nothing changed that I can see. what gives?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-29-2011 09:43 AM
тАО09-29-2011 09:43 AM
Re: feature 441 - Direct to VM transfer not working
no voltage changes?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-13-2011 01:27 PM
тАО10-13-2011 01:27 PM
Re: feature 441 - Direct to VM transfer not working
The telco "made some changes" and the problem has not happened for a week -