After an Ignite B.4.1.61 boot my lvm config is not correct

[Mark Misselbrook]

Server K580 runnning HPUX 11.0 using Ignite B.1.4.61. All VG's are mirrored. After booting from ignite tape the following errors appear in all other volume groups and they appear to be uncorrectable. Is this a known bug in Ignite 4.1.61

# vgdisplay -v /dev/vg03
vgdisplay: Warning: couldn't query physical volume "/dev/dsk/c1t14d0":
The specified path does not correspond to physical volume attached to
this volume group
vgdisplay: Warning: couldn't query all of the physical volumes.
--- Volume groups ---
VG Name /dev/vg03
VG Write Access read/write
VG Status available
Max LV 255
Cur LV 2
Open LV 3
Max PV 16
Cur PV 4
Act PV 3
Max PE per PV 8000
VGDA 6
PE Size (Mbytes) 4
Total PE 4216
Alloc PE 3366
Free PE 850
Total PVG 0
Total Spare PVs 0
Total Spare PVs in use 0

vgdisplay: Warning: couldn't query physical volume "/dev/dsk/c1t14d0":
The specified path does not correspond to physical volume attached to
this volume group
vgdisplay: Warning: couldn't query all of the physical volumes.
--- Logical volumes ---
LV Name /dev/vg03/archive2
LV Status available/syncd
LV Size (Mbytes) 10000
Current LE 2500
Allocated PE 2500
Used PV 3

vgdisplay: Warning: couldn't query physical volume "/dev/dsk/c1t14d0":
The specified path does not correspond to physical volume attached to
this volume group
vgdisplay: Warning: couldn't query all of the physical volumes.
LV Name /dev/vg03/lvol2
LV Status available/syncd
LV Size (Mbytes) 0
Current LE 0
Allocated PE 0
Used PV 0

vgdisplay: Warning: couldn't query physical volume "/dev/dsk/c1t14d0":
The specified path does not correspond to physical volume attached to
this volume group
vgdisplay: Warning: couldn't query all of the physical volumes.
LV Name /dev/vg03/test
LV Status available/syncd
LV Size (Mbytes) 4000
Current LE 1000
Allocated PE 1000
Used PV 1


--- Physical volumes ---
PV Name /dev/dsk/c3t5d0
vgdisplay: Warning: couldn't query physical volume "/dev/dsk/c1t14d0":
The specified path does not correspond to physical volume attached to
this volume group
vgdisplay: Warning: couldn't query all of the physical volumes.
PV Status available
Total PE 1023
Free PE 0
Autoswitch On

PV Name /dev/dsk/c3t6d0
vgdisplay: Warning: couldn't query physical volume "/dev/dsk/c1t14d0":
The specified path does not correspond to physical volume attached to
this volume group
vgdisplay: Warning: couldn't query all of the physical volumes.
PV Status available
Total PE 1023
Free PE 0
Autoswitch On

PV Name /dev/dsk/c5t14d0
vgdisplay: Warning: couldn't query physical volume "/dev/dsk/c1t14d0":
The specified path does not correspond to physical volume attached to
this volume group
vgdisplay: Warning: couldn't query all of the physical volumes.
PV Status available
Total PE 2170
Free PE 850
Autoswitch On


HELP!!!!!!!!!!!!!!!!!!!!!!

[Steven E. Protter]

The reason you may have had to do an ignite recovery is because a disk failed.

Prior to doing an Ignite recovery if possible its always a good idea to check your disks.

diskinfo

dmesg

cstm mstm xstm look for and arrange replacement of any disks that have gone south.

Replace the disk and recovery your system again.

If this isn't a recovery the bad news here is you can't run a good ignite backup without all disks being present and accounted for. Follow the above steps, id and replace the bad disk and the make_tape_recovery will start to work.

Ignite's pickiness may have just done you a HUGE favor.

SEP

[Mark Misselbrook]

The reason for creating the reovery tape is the first place was to provide a clean recover point in case I had to use it, which I have. I appreciate that Ignite will not reover the mirrors and that I have to recover these manually, however the recovery tape has created the situation where I get these lvm errors and therefore cannot reduce the VG's to then create the mirror sets.

More help please