- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- Re: Ignite on 11i NFS Server not responding
Operating System - HP-UX
1753268
Members
5166
Online
108792
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-02-2003 12:41 AM
тАО04-02-2003 12:41 AM
Ignite on 11i NFS Server not responding
I have setup an Ignite Server on an old K210 running 11i with Ignite (both December 2002 Releases & Support+)
When I try to re-build a box from the Ignite image, it fails anywhere between 20% & 80% of the build, with NFS Server not responding.
Any ideas?
When I try to re-build a box from the Ignite image, it fails anywhere between 20% & 80% of the build, with NFS Server not responding.
Any ideas?
-
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-02-2003 01:16 AM
тАО04-02-2003 01:16 AM
Re: Ignite on 11i NFS Server not responding
The NFS not responding error is indicative of your network which cant cope with the consistent speed needed for the ignite build/copy. To fix it add in a couple of nfs mount options;
retry=999,retrans=999
This will stop the NFS server not responding errors.
retry=999,retrans=999
This will stop the NFS server not responding errors.
Im from Palmerston North, New Zealand, but somehow ended up in London...
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-02-2003 03:24 AM
тАО04-02-2003 03:24 AM
Re: Ignite on 11i NFS Server not responding
Seem's it was a patch issue, I installed an additional patch, from support +.
PHKL_25238
This was in addition to PHNE_26388.
PHKL_25238
This was in addition to PHNE_26388.
-
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-05-2003 07:29 PM
тАО04-05-2003 07:29 PM
Re: Ignite on 11i NFS Server not responding
Its probably not a patch issue, though that will help.
Networking can be an issue.
1) You can't boot an Ignite client on anything other than the built in.
2) Do a lanadmin -x lan# replace lan with the lan number you are trying the Ignite pull/push on.
Is it what you expect? Even if it is, check the switch port settings. If the switch is Cisco, have the admin hard code the settings to the max speed on your card. Autonegiate on Cisco switchs confuses HP NIC's.
After that is fun, boot the box, lanadmin -x lan#
If its not what you expect, hard code the settings you want into this file:
/etc/rc.config.d/hpbtlanconf file
Once you have this worked out, you should retry the transfer, it might go better.
If you have the latest pax patch installed, which lets you put 8Gig files into your Ignite image, remove it. The utility pax_iux can't unpack files that big.
Yes, I've had your problem and gotten through it. Been there, done that, got the tee-shirt.
SEP
Networking can be an issue.
1) You can't boot an Ignite client on anything other than the built in.
2) Do a lanadmin -x lan# replace lan with the lan number you are trying the Ignite pull/push on.
Is it what you expect? Even if it is, check the switch port settings. If the switch is Cisco, have the admin hard code the settings to the max speed on your card. Autonegiate on Cisco switchs confuses HP NIC's.
After that is fun, boot the box, lanadmin -x lan#
If its not what you expect, hard code the settings you want into this file:
/etc/rc.config.d/hpbtlanconf file
Once you have this worked out, you should retry the transfer, it might go better.
If you have the latest pax patch installed, which lets you put 8Gig files into your Ignite image, remove it. The utility pax_iux can't unpack files that big.
Yes, I've had your problem and gotten through it. Been there, done that, got the tee-shirt.
SEP
Steven E Protter
Owner of ISN Corporation
http://isnamerica.com
http://hpuxconsulting.com
Sponsor: http://hpux.ws
Twitter: http://twitter.com/hpuxlinux
Founder http://newdatacloud.com
Owner of ISN Corporation
http://isnamerica.com
http://hpuxconsulting.com
Sponsor: http://hpux.ws
Twitter: http://twitter.com/hpuxlinux
Founder http://newdatacloud.com
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP