- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- Re: Save_config not responding
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-28-2007 02:37 AM
тАО11-28-2007 02:37 AM
Re: Save_config not responding
I already mentioned in this thread that all lvm commands are running smoothly. I chked now also and found no problem in lvdisplay of every lvol in vg00.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-28-2007 07:23 AM
тАО11-28-2007 07:23 AM
Re: Save_config not responding
did you notice any format differences in lvdisplay output ?
Hasan.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-28-2007 02:05 PM
тАО11-28-2007 02:05 PM
Re: Save_config not responding
+ process_lvm_volume_group vg00
is a function call to a function called process_lvm_volume_group. The posix shell does not keep set -x active through a function call. You might consider placing set -x at the start of the function call and see where it stops in that function.
If save_config has stopped when it has ran the get_system_info command run save_config as follows:
# tusc -kpaEef -o (output file) \
/opt/ignite/bin/save_config vg00
Note that the output file produced will probably be quite large.
More than likely you have a disk LUN presented to the system that responds to SCSI inquiry commands but does not respond if you attempt to open a read it. Your only choice will be to unpresent the LUN.
Look for the syscall entry that never returns (may take a while but will be towards the end) and if it's a read system call track back the fd to where it was opened and get the name of the device.
Good Luck.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-28-2007 09:32 PM
тАО11-28-2007 09:32 PM
Re: Save_config not responding
Thanks for the reply. Your command still dont yeild any new things.. same things happening and we dont have any LUN kinda stuff on our server.
Hasan,
There are no such remarkeble odd things in lvdislpay too..!!
Any more suggestions???
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-28-2007 11:20 PM
тАО11-28-2007 11:20 PM
Re: Save_config not responding
I checked out file and got execution is stucking at this line:
[13691] lseek64(5, 8192, 0, SEEK_SET, 0) .............................................................................. = 8192
[13691] read(5, 0x7f7f1040, 8192) ..................................................................................... [entry]
any clue??
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-29-2007 09:04 AM
тАО11-29-2007 09:04 AM
Re: Save_config not responding
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-29-2007 09:07 AM
тАО11-29-2007 09:07 AM
Re: Save_config not responding
If it's a FIFO instead of a device find out what process has the other end of the fifo and what it is doing.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-29-2007 12:20 PM
тАО11-29-2007 12:20 PM
Re: Save_config not responding
Someone within HP will then look at the tusc trace. You may also be asked for a debug run of save_config:
# export INST_DEBUG=5
# script
# save_config ...
# exit
The file created is called typescript in the current working directory (look at the script manual page for information on how to change the name). Provide that file to HP and there is another file you should provide: /tmp/*listener.log if it contains anything.
- « Previous
-
- 1
- 2
- Next »