- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- ignite from K-class to be restored in R-class serv...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-22-2005 09:45 PM
тАО09-22-2005 09:45 PM
I need to do a restoration on the R-class server using an ignite made from a K-class. Since both have different devices installed (number of disks, cards, adapters), will the restoration be successful? Do you have a step by step procedure on how to go about it?
Many Thanks,
AfterBurN
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-22-2005 09:50 PM
тАО09-22-2005 09:50 PM
Re: ignite from K-class to be restored in R-class server
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-22-2005 10:35 PM
тАО09-22-2005 10:35 PM
Re: ignite from K-class to be restored in R-class server
In this case, an R & a K are reasonably close in system type so I think it should work.
Any devices not in the original load should be added by ioinit at the initial boot after the recovery.
At worst, you may have to add a driver or two post-recovery.
But remember to apply the latest QPK, HWE & DIAG bundles afterwards anyway.
HTH,
Jeff
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-23-2005 01:37 AM
тАО09-23-2005 01:37 AM
Solutionhttp://www.docs.hp.com/en/IUX/
Bill Hassell, sysadmin
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-25-2005 01:03 AM
тАО09-25-2005 01:03 AM
Re: ignite from K-class to be restored in R-class server
1. Hardware architecture of R Class and K Class is different, so there will be drivers issues
2. OS point of view there should not be any issue
Good Luck
Regards
Mahesh