- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - Linux
- >
- Re: Configure hpsmh after image nodes.
Operating System - Linux
1752273
Members
4612
Online
108786
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Go to solution
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-13-2007 09:06 PM
тАО06-13-2007 09:06 PM
Hello.
I notice that after deploy images , I can not
access the hpsmh. donig lsof i can see port 2301 bind only to localhost. I can fix it with /usr/local/hp/hpSMHSetup.pl . but on standrd installation the hpsmh bind to the server hostname too.
Is there a problem using the perl script ? or should i leave this binding as is.
regards
Shalom Klemer
I notice that after deploy images , I can not
access the hpsmh. donig lsof i can see port 2301 bind only to localhost. I can fix it with /usr/local/hp/hpSMHSetup.pl . but on standrd installation the hpsmh bind to the server hostname too.
Is there a problem using the perl script ? or should i leave this binding as is.
regards
Shalom Klemer
Solved! Go to Solution.
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-20-2007 04:36 AM
тАО06-20-2007 04:36 AM
Solution
If you installed the SMH component via ICLE using one of the "Install Proliant Support Pack for RHEL/SLES" task chains, the SMH configuration should be set to be visible to ICLE via the blade Manage page. If you installed the SMH component manually, you must configure it manually. Specifically to make the SMH visible to ICLE you must allow ICLE access via the SMH configuration (we set IP-BINDING="YES" and IP-BINDING-LIST="" for example).
Hope this helps with the issue.
Dan
Hope this helps with the issue.
Dan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-22-2007 03:40 AM
тАО06-22-2007 03:40 AM
Re: Configure hpsmh after image nodes.
Thanks !!!
I will check the config file on customer site.
We installed the PSP with the ICLE script,
And now i understand that the hpsmh visible only to icle subnet.
Thanks again.
Shalom.
I will check the config file on customer site.
We installed the PSP with the ICLE script,
And now i understand that the hpsmh visible only to icle subnet.
Thanks again.
Shalom.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP