- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - Linux
- >
- ICLE 1.6 and BL465c - iLO going pack to "zero" IP
Operating System - Linux
1748167
Members
4021
Online
108758
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-19-2007 02:51 AM
тАО06-19-2007 02:51 AM
ICLE 1.6 and BL465c - iLO going pack to "zero" IP
New ICLE 1.6 install.
2 7000 chassis loaded with BL465c (1.8s, 16GB, dual drives)
Added 326m, Quad pass-thrus (if it matters)
External switching is Foundry (basic setup, dedicated switch, no VLANs)
On discovery, blades are randomly setting their iLO IP to 0.0.0.0. Typically 4 to 6 blades in each chassis. Some of them "come back" after a while, some of them don't come back until the blade is pulled from the chassis & reseated.
ALL iLO were verified for firmware rev and set to DHCP.
I have not had opportunity to look at the chassis today, but when I left it last night it had at least stabilized. So it appears that this was just in the first hours around initial discovery.
Is there an explanation for this? Customer less than thrilled with ICLE/H-P Blades ATM......
TIA
Don
2 7000 chassis loaded with BL465c (1.8s, 16GB, dual drives)
Added 326m, Quad pass-thrus (if it matters)
External switching is Foundry (basic setup, dedicated switch, no VLANs)
On discovery, blades are randomly setting their iLO IP to 0.0.0.0. Typically 4 to 6 blades in each chassis. Some of them "come back" after a while, some of them don't come back until the blade is pulled from the chassis & reseated.
ALL iLO were verified for firmware rev and set to DHCP.
I have not had opportunity to look at the chassis today, but when I left it last night it had at least stabilized. So it appears that this was just in the first hours around initial discovery.
Is there an explanation for this? Customer less than thrilled with ICLE/H-P Blades ATM......
TIA
Don
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-20-2007 04:19 AM
тАО06-20-2007 04:19 AM
Re: ICLE 1.6 and BL465c - iLO going pack to "zero" IP
Don, have you verified your version of iLO2 firmware and OA firmware ?
I will do some research, but I seem to remember this being fixed in a firmware upgrade. :)
Robert
I will do some research, but I seem to remember this being fixed in a firmware upgrade. :)
Robert
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-20-2007 06:11 PM
тАО06-20-2007 06:11 PM
Re: ICLE 1.6 and BL465c - iLO going pack to "zero" IP
Yep - they're all 1.29 "Blade Version"
All Blades are OK now except for ONE that does not show a device model when looking at the Blades under the OA web interface. It shows a "1. " but that's it (whereas Blade 2 shows "2. BL465c yada yada"
All Blades are OK now except for ONE that does not show a device model when looking at the Blades under the OA web interface. It shows a "1. " but that's it (whereas Blade 2 shows "2. BL465c yada yada"
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP