- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - Linux
- >
- Re: failed to deploy an image ice V2.01
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-30-2009 06:32 PM
тАО04-30-2009 06:32 PM
Re: failed to deploy an image ice V2.01
Thanks.
I can open a new case & send you sosreport if you wish. we tried the capture 3 times with same results. we even export vgcrash but got same results.
we tried to delete all none relevant disks from the xml file including vgcrash & on the partition page we got the partition table.
we saw as mountpoint only / + /opt .all other lvols were without mountpoint.
the Deploy start o.k. but failed later
regards
Shalom.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-08-2009 07:28 AM
тАО05-08-2009 07:28 AM
Re: failed to deploy an image ice V2.01
Can you try this?
* Remove the non-essential (odd) partition with the two "pvdevice"s. This should allow the partition wizard GUI to load properly.
* For any partition in the wizard that does not show a mount point, edit that partition and set its mount point. Each partition must have a mount point set, but the partition wizard incorrectly assumes that the partition "label" contains the mount point and that is not always the case. This issue has recently been release noted. Setting the mount point by hand by editing the partition information is the workaround.
* Once all partitions have mount points set in the partition wizard, "continue" in the partition wizard and perform the deploy.
I would like to know if the above steps result in a successful deploy.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-08-2009 07:39 AM
тАО05-08-2009 07:39 AM
Re: failed to deploy an image ice V2.01
O.K. thanks !!!!!!
I just sent what you asked to customer.
hoping for quick answer.
Regards
Shalom.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-28-2009 10:32 AM
тАО05-28-2009 10:32 AM
Re: failed to deploy an image ice V2.01
a bad capture (two pvdevice entries).
What can we do to reproduce the bad capture? Do you understand what about
your configuration is causing that to happen?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-03-2009 12:42 AM
тАО06-03-2009 12:42 AM
Re: failed to deploy an image ice V2.01
I am sorry for the delay.
i wasnt working for 3 weeks.
Customer told me he cant tests the systems since its goes to production.
he will do some tests on other systems in the next 2 weeks.
I will soon close the case.
Thank for your help !!!!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-03-2009 02:02 AM
тАО07-03-2009 02:02 AM
Re: failed to deploy an image ice V2.01
Our Error happened again with other system.
this system connect to EMC too , but the OS is on local disks.
We did what Mark suggested & its worked. The deploy works fine on one system & failed on another , But from the deploy error on second bl460c its seems like a known problem , which V2.10 solves.
"aer : probe of 000xxx:pcie01 failed with error 2"
I opened a case regarding the double PV. I will send the image xml file & sosreport from source bl460c.
Best Regards.
Shalom.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-26-2009 12:08 AM
тАО08-26-2009 12:08 AM
Re: failed to deploy an image ice V2.01
Sorry for the Delay.
i got an answer , to upgrade the ICE version to solve the problem.
thanks to all.
Shalom.
- « Previous
-
- 1
- 2
- Next »