- Community Home
- >
- Services
- >
- Insight Remote Support
- >
- Can You Run RSP On Proliant Blades
Insight Remote Support
1753536
Members
6660
Online
108795
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-01-2008 08:26 AM
тАО05-01-2008 08:26 AM
Can You Run RSP On Proliant Blades
The RSP sizing tool does not mention Proliant Blades. Can they be used to run SIM/RSP?
Thanks,
Steve
Thanks,
Steve
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-02-2008 04:07 AM
тАО05-02-2008 04:07 AM
Re: Can You Run RSP On Proliant Blades
Steve,
According to the document below:
http://docs.hp.com/en/5992-4820/5992-4820.pdf
CMS with RSP System Access Requirements
You must have administrative rights both on the Central Management Server (CMS) and in HP Systems Insight
Manager (HP SIM) to access both the Remote Support Software Manager (RSSWM)and the Remote Support
Configuration and Services option in HP SIM.
Supported Hardware
├в ┬в Any HP ProLiant x86 system running a supported OS that meets the minimum specifications
├в ┬в Any HP ProLiant x64 system running a supported OS that meets the minimum specifications
IMPORTANT: Though not required, HP strongly recommends that the Central Management Server (CMS)
be covered by either warranty, HP Care Pack, or HP support contract obligation, since the CMS is a critical
component of the Remote Support Solution.
Minimum Specifications
├в ┬в 2.4-GHz processor with 2 GB RAM
├в ┬в 500 MB free disk space
Recommended Specifications (if more than 100 Managed Systems will be Monitored)
├в ┬в 2.4-GHz processor with 4 GB RAM
├в ┬в 500 MB free disk space
NOTE: The following Hardware is NOT SUPPORTED FOR A CMS hosting RSP HP ProLiant 1xx Series
servers, HP Netservers, Virtual Machines. For more information about why these hardware systems are not
supported please see the RSP Release Notes at:
http://docs.hp.com/en/netsys.html#Service%20Essentials%20Remote%20Support%20Pack
Please refer to the above doc for more details.
Hope this helps,
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-02-2008 04:19 AM
тАО05-02-2008 04:19 AM
Re: Can You Run RSP On Proliant Blades
Thamks
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP