- Community Home
- >
- Servers and Operating Systems
- >
- Integrity Servers
- >
- Access ILO from hpux
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-03-2015 11:14 AM
тАО11-03-2015 11:14 AM
Re: Access ILO from hpux
It doesn't work.
I get addr from the frontal card.
Then i connect directly to my eth0 laptop,and doesn't work
i use on linux
arp -s 192.168.0.123 00:**:**:**:**:**
Then i connect to switch(and i see only one light is green,the other is off)
Then i try XP
arp -s 192.168.0.123 00-**-**-**-**-**
Nothing
i do last try now,connect directly to router: will work?I think no
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-03-2015 11:39 AM
тАО11-03-2015 11:39 AM
Re: Access ILO from hpux
You wrote
>> I can see the output on terminal laptop via nullmodem
What happens if you press <CTRL> e followed by c and f ?
This should give you write access.
Make sure the serial cable is connected to the 24pin connetor at the MP card.
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-03-2015 11:53 AM - edited тАО11-03-2015 11:56 AM
тАО11-03-2015 11:53 AM - edited тАО11-03-2015 11:56 AM
Re: Access ILO from hpux
I have no cable of 25pin,i have ordered one.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-03-2015 11:57 AM
тАО11-03-2015 11:57 AM
Re: Access ILO from hpux
>> >> I can see the output on terminal laptop via nullmodem
What exactly do you see?
Where is your cable connected?
After connecting the power cables, you should see
HP Management Processor
Firmware Revision E.03.28 May 24 2006,20:30:11
(c) Copyright Hewlett-Packard Company 1999-2006. All Rights Reserved.
*************************************************************************
This is a private system.
Do not attempt to login unless you are an authorized user.
Any authorized or unauthorized access or use may be monitored and can
result in criminal or civil prosecution under applicable law.
*************************************************************************
*************************************************************************
Only default users are configured.
Use one of the following user/password pairs to login:
Admin/Admin
Oper/Oper
*************************************************************************
MP login:
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-03-2015 12:33 PM
тАО11-03-2015 12:33 PM
Re: Access ILO from hpux
Finally i found solution,the arp -s suggested by Hassel works fine.
Thanks to all for help,the problem was my network some pc cannot reach
the 10.2.0.44 static address given to hpilo via arp -s.
Only one(the pc with 10.2.0.1) can reach it,the other with route static
configured not.
This time i check with this command
/opt/propplus/bin/cprop -summary -c "Management Processor"
And i see the 10.2.0.44 static address
- « Previous
- Next »